Stanton SK 6F - Manual (Page 4)

F A D E R C L E A N I N G
The SK FOUR faders may need lubrication from time to time. This will extend
the fader life and eliminate any potential damage due to extended heavy usage.
Follow the instruction below the lubricate your faders:
ROTATING AND REPLACING THE INPUT SWITCHES
1. Remove the 3 fader knobs and 4
screws located in the corners of the
face plate and take the plate off the
mixer.
2 . Remove the fader to be cleaned by
unscrewing the 2 outer screws (remov-
ing the 2 inner screws will detach the
fader from the fader plate) and discon-
nect the cable coming from the mixer.
3. Spray a small amount of cleaner or
lubricant into both ends of the fader
and slide the fader back and forth a few
times to spread the fluid evenly
throughout the fader.
4. Shake and wipe off excess fluid
before re-assembling the fader.
T E C H N I C A L S P E C I F I C AT I O N S
Line inputs: 2 (RCA), 150 mV / 27K ohm
Phono inputs: 2 (RCA), 3 mV / 47K ohm
Send: 2 (1/4”), 150 mV / 27K ohm
Return: 2 (1/4”), 775 mV / 1K ohm
DJ mic input: 1 (1/4 inch), 1.5 mV / 3K ohm
Master output: 1 (1/4” TRS Balanced/RCA unbalanced),
1.2 V / 100 ohm
Record output: 1 (RCA), 245 mV / 100 ohm
Headphone output: 1 (1/4 inch), 32 - 200 ohms recommended
Frequency Response: 20 Hz - 20 kHz, +/- 2 dB
Tone Control : + 9/-26 dB (Hi, Low)
Gain Control: 20dB / 1 Khz
S/N Ratio: Less than 70dB
T.H.D: less than 0.2%
Dimension(LxWxD): 12 3/8” x 10 1/4” x 4” ( 314 x 260 x 102 mm)
Weight: 7 lbs (3.2 Kg)
R E P L A C E M E N T PA RT S
To replace the cross or channel faders, follow steps 1 and 2 of the
cleaning instructions. The following replacement parts are available
from Stanton or your local Stanton dealer.
LF-SK6 Channel fader
CF-SK6 Crossfader
CFF1 Focus Fader
PP-SK6F Silver face plate
PP-SK6F-B Blue face plate
PL-SK6 Two way input toggle switch
3PL-SK6 Three way input toggle switch with FLASH
PS-18US US Power Supply (110v)
PS-18EU European Power Supply (220v)
PS-18UK UK only Power Supply (240v)
ROTATING INSTRUCTIONS
1 . Remove the PROTEKT™ panel
(Cleaning instructions step 1)
2. Remove the 2 outer screws from
the toggle switch plate (removing the
2 inner screws will detach the switch
from the plate)
3. Rotate the plate to the desired posi-
tion and tighten the screws back in
the top and bottom holes
REPLACING INSTRUCTIONS
1. Remove the PROTEKT™ panel
(Cleaning instructions step 1)
2. Remove the 2 outer screws from
the toggle switch plate (removing the
2 inner screws will detach the switch
from the plate)
3. Remove the switch assembly and
disconnect the cable coming from the
mixer.
4. Set the replacement switch assem-
bly in the desired position and place
the screws back in the top and bottom
holes.
This unit has been designed and manufactured using quality components.
Therefore, it is warranted to be free from defects in materials (limited as specified
below), and workmanship for a period of twelve (12) months from the original pur-
chase date. During this period, all service and parts necessary to repair a defect
will be free of charge. This limited warranty applies to mechanical parts which are
subject to wear and tear as specified:Faders, specified durability: 15,000 cycles;
Rotary potentiometers, specified durability: 10,000 cycles; Switches, specified
durability: 10,000 cycles. Consequently, the parts listed above are warranted to
be free from defects in materials and workmanship for a period of thirty days (30)
days from the original purchase date.
For the warranty to be valid, please complete the warranty registration card
attached or fill out the online registration
at www.stantonmagnetics.com
Mail completed warranty cards to:
Stanton Magnetics, LLC, 2821 Evans Street • Hollywood, FL 33020
WA R R A N T Y