Sony XAV-W1 - Manual (Page 55)

55
The contents of the memory have been erased.
• The reset button has been pressed.
t Store again into the memory.
• The power supply lead or battery has been
disconnected.
• The power supply lead is not connected properly.
Stored stations and correct time are erased.
The fuse has blown.
Makes noise when the position of the ignition
is switched.
The leads are not matched correctly with the car’s
accessory power connector.
The display disappears from/does not appear
on the monitor.
• The dimmer is set to “ON” (page 41).
• The display disappears if you press and hold (OFF).
t Press and hold (OFF) on the unit until the
display appears.
• is touched and the Monitor Off function is
activated (page 11).
t Touch anywhere on the display to turn back on.
The display does not respond to your touch
correctly.
• Touch one part of the display at a time. If two or more
parts are touched simultaneously, the display will not
operate correctly.
• Adjust the touch point of the display (page 33).
The Auto Off function does not operate.
The unit is turned on. The Auto Off function activates
after turning off the unit.
t Turn off the unit.
Card remote commander operation is not
possible.
• If the Monitor Off function is activated (no lighting),
card remote commander operation is not possible
(page 11).
• Make sure the insulation film has been removed
(page 14).
The menu items cannot be selected.
Unavailable menu items are shown in grey.
AUX cannot be selected as the source.
All AUX input settings are set to “OFF.”
t Set “AUX 1”/“AUX 2”/“AUX 3” to “Video” or
“Audio” (page 42).
Picture
There is no picture/picture noise occurs.
• A connection has not been made correctly.
• Check the connection to the connected equipment,
and set the input selector of the equipment to the
source corresponding to this unit.
• Defective or dirty disc.
• Installation is not correct.
t Install the unit at an angle of less than 45° in a
sturdy part of the car.
• The parking cord (light green) is not connected to the
parking brake switch cord, or the parking brake is not
applied.
Picture does not fit in the screen.
The aspect ratio is fixed on the DVD.
The picture does not appear in the rear
monitor.
• The source/mode which is not connected is selected.
If there is no input, no picture appears in the rear
monitor.
• The picture of the back camera/navigation device is
displayed on this unit.
t No picture appears in the rear monitor if the
picture of the back camera/navigation device is
displayed on this unit.
Sound
There is no sound/sound skips/sound cracks.
• A connection has not been made correctly.
• Check the connection to the connected equipment,
and set the input selector of the equipment to the
source corresponding to this unit.
• Defective or dirty disc.
• Installation is not correct.
t Install the unit at an angle of less than 45° in a
sturdy part of the car.
• The MP3 file sampling rate is not 16, 22.05, 24, 32,
44.1, or 48 kHz.
• The WMA file sampling rate is not 32, 44.1, or
48 kHz.
• The MP3 file bit rate is not 8 to 384 kbps.
• The WMA file bit rate is not 32 to 384 kbps.
• The unit is in pause/reverse/fast-forward mode.
• The settings for the outputs are not made correctly.
• The DVD output level is too low (page 22).
• The volume is too low.
• The ATT function is activated, or the Telephone ATT
function (when the interface cable of a car telephone
is connected to the ATT lead) is activated.
• The center speaker or subwoofer configuration is
incorrect (page 32).
• The position of the fader control “Fader” is not set for
a 2-speaker system.
• The CD changer is incompatible with the disc (MP3/
WMA).
t Play back with this unit.
Sound is noisy.
• Keep cords and cables away from each other.
• If an Super Audio CD is played and “Super Audio
CD Mode” is set to “High Quality,” instead set to
“Standard” (page 28).
continue to next page t