Smeg AS62C - Manual (Page 9)

9 - EN
Auxiliary function
Low temperature
This function allows for drying at lower
temperatures and therefore saves energy.
Warning LED will light up when you select
the function.
C
You must use this function when you
dry your synthetic or delicate laundry.
Warning indicators
C
Warning indicators may differ
according to the model of your machine.
Filter cleaning
A warning LED will light up to remind filter
cleaning after the program finishes.
C
If the filter cleaning warning LED lights
up continuously, please refer to, “Solution
suggestions for problems”.
Water tank
A warning LED will light up at the end of the
program or when the tank is full with water. The
machine stops operating when this warning LED
lights up during a program running. To restart
the machine, please drain the water in the water
tank. Press “Start/Pause/Cancel” button to
start the program after you have emptied the
water tank. The warning LED goes off and the
program resumes operating.
Starting the Program
1. Press “Start/Pause/Cancel” button to start the
program.
2. “Start/Pause/Cancel” button will light up to
indicate that the program has started.
Timer follow-up indicator
One of the lamps is on as far as program runs
and shows the approximate remaining time.
C
LEDs on the timer follow-up indicator
will also flash when the child-proof lock is
activated.
C
If more than one LED light up or flash
concurrently, it means there is malfunctioning
or a failure (please see, Solution suggestions for
problems).
Changing the program after the
program has started
You can use this feature to dry your laundry in a
different program after your machine has started
to run.
For example;
Press and hold the “Start/Pause/Cancel” button
for about 3 seconds to select “80” minutes
program instead of “60” minutes program.
Select the “80” minutes program by rotating the
program knob.
Press “Start/Pause/Cancel” button to start the
program.
C
The program which is selected first will
go on even if the program selection button
is moved and another program mode is
selected while the machine is operating. You
must cancel the ongoing program in order to
change the drying program. (See, Ending the
program through canceling)
Adding/removing laundry in standby mode
In order to add or take out laundry after the
start-up of the program;
1. Press the “Start/Pause/Cancel” button to
switch the machine to “Pause” mode. Drying
process will stop.
2. Open the door at Pause position and close it
again after adding or taking out laundry.
3. Press “Start/Pause/Cancel” button to start the
program.
C
Any laundry added after the drying
process was started may cause the already
dried clothes in the machine intermingle with
wet clothes and the result will be wet laundry
after the drying process is over.
C
Laundry may be added or taken out
as much as desired during a drying process,
but as this process will interrupt drying
continuously, it will extend the program
duration and increase energy consumption.
Therefore, it is recommended to add laundry
before the drying program is started.
Child-proof lock
There is a childproof lock to prevent any
program interruption due to the pressing of
keys while the program is on. The loading
door and all keys except the “On/Off” key
on the panel are deactivated when the child-
proof lock is active.
In order to activate the childproof lock, press
on the “Start/Pause/Cancel” and “Low
temperature” buttons simultaneously for 3
seconds.
To start a new program
after the program is
over or to interrupt
the program, the
childproof lock should be
deactivated. To deactivate
the childproof lock, press the same buttons for
3 sec.
C
One of the LEDs on the program
follow-up indicator starts flashing when the
child-proof lock is activated.
Ending the program through canceling
The program which is selected first will keep
on going even if the position of the program
selection button is changed. A new program can
be selected and started after “Program cancel”
is activated in order to change the drying