Skylink MD-318 - Manual (Page 2)

5. OPERATION (CONT)
This receiver offers two optional states after powered on, choose the one
which fits your requirement.
1. Power On - Light On:
1) You may use the wall switch to control the light as usual. When the
wall switch is off, the light is off. When the wall switch is on, the light is
on.
2) After a power outage and the electricity comes back, the light will be
on if the wall switch is in On position.
2. Power On - Light Off:
1) A special sequence is needed to turn on the light by the wall switch.
To turn on the light by the wall switch: 1) Switch On, 2) Switch Off,
3) Switch On again within 2 seconds. Light will be on.
2) After a power outage and electricity comes back, the light will be off
under most of the circumstances.
To toggle a receiver between these two states, re-program a transmitter
twice consecutively to the receiver. Referring to Section 3, repeat the
programming steps twice consecutively with a transmitter that is already
programmed, the receiver will change state.
Input Voltage: 120VAC , 60Hz
Maximum Load: 300W at 120VAC
Operating Frequency: 318MHz
Range: Up to 500 feet in open area
Standby Current: 6mA
Minimum Load: 10W
Operational Temperature: -4° F - 140° F (-20° C - 60° C)
Humidity: 5%-95%
7. TECHNICAL SPECIFICATIONS
6. ERASING TRANSMITTERS FROM THE
ON/OFF/DIMMING CONTROL
8. FCC
The Remote Control is approved by the FCC and it complies with Part 15 of the
FCC Rules. Its operation is subject to the following two conditions :
1. This device may not cause harmful interference.
2. This device must accept any interference that may cause undesired operation.
WARNING:
Changes or modifications to this unit not expressly approved by the party responsible
of compliance could void the user’s authority to operate the equipment.
9. WARRANTY
If, within one year from date of purchase, this product should become defective
(except battery), due to faulty workmanship or materials, it will be repaired or
replaced, without charge. Proof of purchase and a Return Authorization are required.
You may erase a transmitter from the ON/OFF/Dimming Control, but you
cannot erase a specific device directly, you must erase all the wireless
devices, then program the ones you want to keep. Follow the instructions
below to erase programmed transmitters.
1. Power off the lighting receiver. (Switch off the wall switch)
2. Transmit a "Erase" code from the transmitter until step 4.
3. Power up the ON/OFF/Dimming Control (Switch on the wall switch),
you will hear a beep.
4. You may stop the "Erase" code signal transmission, the ON/OFF/
Dimming Control will beep, indicating you have successfully erased all
the devices from the ON/OFF/Dimming Control.
To erase other transmitters / sensors, please refer to the instructions of
the transmitters / sensors.
11. ACCESSORIES
The Skylink System consists of many other devices such as
SkylinkHome Remotes, Motion Sensor, ON/OFF Wall Switch, Wall
Dimmer, Plug-In Dimmer with or without Repeater, Plug-In ON/OFF
Control (Outdoor/Indoor), Screw-In Dimmer, ON/OFF/Dimming Control,
ON/OFF Control, Smart Button Garage Door Control, etc. Please visit
Skylink website at www.skylinkhome.com for more information.
TM Home
TM
TM
10. CUSTOMER SERVICE
If you would like to
· find out the up-to-date specifications
· know more about features and applications
· download documents, i.e. user’s instructions
· order Skylink products
or if you have difficulty getting products to work, please:
1. visit our FAQ section at www.skylinkhome.com, or
2. email us at [email protected], or
3. call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST.
Fax (800) 286-1320
CUSTOMER SERVICE
17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3
Email:[email protected]
http://www.skylinkhome.com
P/N. 101Z699
Patent Pending
©2010 SKYLINK GROUP
In case the transmitter is not on hand, you can still operate the lighting
fixture with the wall switch.