Speco Technologies HT65010XW - Manual

PRECAUTION
1. You can install the camera indoors or outdoors.
2. Choose an ideal location for the camera, since a camera
unit must be protected against vibration.
3. Be careful not to scratch the lens or dome cover.
4. Use the camera within the temperature(-10 ~ +50 ).
5. Handle with care. Dropping it can cause serious dam-
age to the camera.
6. Avoid any direct sun light toward the lens.
7. Use the AC adaptor 12V DC regulated.(1A recom-
mendddded)
(24V AC available-Dual power version only) of time.
FEATURES
1. IP67(Waterproof)
2. Durable MATERIAL : Body-Aluminum,
Dome : Polycarbonate
3. Wall & Ceiling mount available
4. New method to adjust the camera direction
DIMENSION
INSTALLATION
1-1. Ceiling mount installation
1-2. Mounting camera to electrical box
1-3. Pipe application
(1) Remove the bolt, the cable fixing screw and the
cable plug on the bottom of the base.
(2) Use the TEPLON tape to wipe the pipe.
(3) After distributing cables, combine the pipe with the
base.
1-4. Camera direction adjustment and fixing
(1) Cover can be installed four directions using two screws
beside the cover.
(2) After loosening two screws on the cover, you can
adjust the direction of camera.
(3) You can tighten up two screws again to fix the direction.
2. Wall mount installation
3. Finishing installation
CONFIGURATION
HOW TO USE THE JOG LEVER
(1) MENU : To access the main setup menu. Push
this button for 1 second.
(2) TELE / UP : To close in on a far object.(ZOOM-IN)
/To move the arrow indicator to up.
(3) WIDE / DOWN : To widen the view.(ZOOM-OUT)
/ To move the arrow indicator to down.
(4) NEAR / LEFT : To see a near object clearly.
/ To move the arrow indicator to left.
(5) FAR / RIGHT : To see a far object clearly.
/ To move the arrow indicator to right.
(6) EXT. VIDEO : Plug your test monitor in here.
(The cable is option)
CAMERA FUNCTION SETTING
MAIN SETUP
OFF CAMERA
TITLE
ON
Set Camera Title String and
OSD Display Position.
ATW–MODE :
OUTDOOR
INDOOR
ATW is controlled by color
tem-perature range
*MODE
- INDOOR : 3000~10,500°K
- OUTDOOR : level
AWC SET ONE PUSH
WHITE BAL
MANUAL RED / BLUE Adjustable.
BACKLIGHT
OFF / LOW /
MIDDLE /
HIGH
Backlight compensation.
OFF Motion detection off
MOTION
DETECTION
ON
AREA(4 Programmable zone/
SIZE)
The
words "MOTION
DETECTED" appear on the
screen and MD output signal
when movement is detected.
FOCUS Refer to focus setup
EXPOSURE Refer to exposure setup
SPECIAL Refer to special setup
RESET
Returns to the level which was
set by the manufacturer for
shipment.
(except for communication and
Day & Night)
EXIT Saves all settings, then exits.
FOCUS SETUP TABLE
AUTO
Focus is controlled
automatically
MANUAL Focus is controlled manually
MODE
ONE-PUSH
Focus is automatically adjusted
just once, after zoom position
is changed.
OFF Zoom tracking off
ZOOM TRK
ON Zoom tracking on
ZOOM SPEED FAST / SLOW Zoom speed Control
ON
Digital zoom limit selectable
(x2 ~ x10).
D-ZOOM
OFF Digital zoom off
ON
Zoom magnification set at power
on (x1 ~ x10)
DIS ZOOM
MAG
OFF Zoom magnification display off
ON Zoom magnification display on.
ZOOM POS
INIT
OFF
When initialized, zoom position
is disabled.
LENS INIT Execute lens initialization.
EXPOSURE SETUP TABLE
BRIGHTNESS Brightness level adjustment.
MANUAL IRIS is controlled manually.
IRIS
AUTO IRIS is controlled automatically.
MANUAL Shutter is controlled manually
SHUTTER
A. FLK Anti-flicker
OFF Automatic gain control off.
AGC NORMAL /
HIGH
Automatic gain control limit set.
OFF Noise reduction off.
SSNR LOW /
MIDDLE /
HIGH
Noise reduction level set.
OFF Sense-up off
SENS-UP
AUTO
Sense-up limit selectable
(x2 ~ x128)
SPECIAL SETUP TABLE
OFF Turns function off
USER PRESET
ON
Using the position preset function,
8 sets of camera shooting
conditions can be stored and
recalled.
OFF Privacy mask off
PRIVACY
ON
AREA(4 Programmable zone)
/ SIZE / TONE adjustable.
COLOR
IR-Cut Filter is fixed to color
position.
B/W
IR-Cut Filter is fixed to B/W
position.
Day Night
AUTO 1, 2
When Input luminance level is
low, IR Cut Filter is switched
to
the B/W position for
increasing
infrared sensitivity automatically.
And, it switches back to Color
position when luminance
is quite increased. Auto 1
mode is switched to IR Cut
Filter more quickly than Auto
2.
INT Internal Sync.
SYNC
LL
External Sync(can adjust
desired phase from 0° ~ 359°).
Trigger Signal: Auto Detection.
COMM ADJ Refer to communication setup
IMAGE ADJ Refer to communication setup
If the product is to be put out of operation
definitively, take it to a local recycling plant for a
disposal which
is not harmful to the environment.
HT65010XS, HT65010XW