Deck lift system – Snapper ZM6100M User Manual
Page 37
37
DECK LIFT SYSTEM
ITEM
PART
NO.
DESCRIPTION
1
1-4354
WASHER, 29/32” I.D. x 1-1/4” O.D.
2
1-5020
RING, 7/8” External Retaining
3
3-4453
WASHER, 25/32” x 1-1/2” Flat (ZM Series 0 Models Only) (2)
4
4-3801
BRACKET, Deck Height Quadrant
5
4-3803
BRACKET, Deck Support (4)
6
4-3819
PLATE, Rear Link (4.95” long) (2) (ZM Series 0 Models Only)
--
7-2422
PLATE, Rear Link (4.33” long) (2) (ZMT, MZM & ZM Series 1 & 2 Models)
7
4-3823
WELDMENT, Lift Handle Link
8
4-3827
LIFT, Front Deck (ZM Series 0 Models Only)
8A
5-8741
LIFT, Front Deck (ZMT, MZM & ZM Series 1 Models)
9A
4-6404
WELDMENT, Shaft Deck Lift (ZM Series 0 Models Only)
9B
5-8225
WELDMENT, Shaft Deck Lift (ZMT, MZM & ZM Series 1 & 2 Models)
10
7-3196
PLATE, Front Link (5.45” long) (2) (ZM Series 0, 1 & 2 & ZMT Models)
--
7-3197
PLATE, Front Link (5.20” long) (2) (MZM Model Only)
11A
4-4859
SWIVEL, Spring Anchor (ZM Series 0 Models Only) (2)
11B
4-6412
BRACKET, Spring Adjustment (2) (ZMT, MZM & ZM Series 1 & 2 Models)
12
4-4860
EYEBOLT, 5/16-18 x 3” (2)
13
7-2225
SPRING, Extension Lift Assist (2)
14
4-4870
PLATE, Shim (6)
15
1-5019
PLUG,
Rod
16
5-4543
ASSEMBLY, Pivot Plate (Includes 4-3804 Weldment, 1-3864 Lube Fitting
and two 1-8289 Sleeve Bearings)
17
4-4857
WELDMENT, Timing Rod
18
9-0820
NUT, 3/4-16 Hex Jam Lock (used on ZM Series 0 Only) (2)
19
9-1194
WASHER, 17/32” x 1-1/2”
20
9-0188
WASHER, 11/32” x 11/16” Flat (8)
21
9-1298
NUT, 5/16-18 Hex Nylon Insert (8)
22
9-1299
NUT, 3/8-16 Hex (7)
23
9-0122
WASHER, 3/8” Flat (4)
24
9-1587
WASHER, 17/32” x 1-1/16” (8)
25
9-1612
BOLT, 5/16-18 x 1-1/2” Carriage Grade 5 (4)
26
9-1640
BOLT, 3/8-16 x 1” Carriage (5)
27
9-1714
BOLT, 5/16-18 x 1-1/2” Carriage Grade 5 (4)
28
9-1809
PIN, 1/8” x 1-1/4” Cotter (3)
29
9-1894
NUT, 1/2-13 Hex Center Lock Grade 5 (3)
30
4-4833
ROD, Lift Lever
31
1-9363
GRIP, Lift Lever Handle
32
1-4361
CAP, Lift Rod
33
1-4432
SPRING
34
4-3833
WELDMENT, Deck Lift Lever
35
1-4437
PIN, 1/4” x 2-1/4” Groove
36
4-4858
SWIVEL, Timing Rod
37
9-1947
PIN, 1/8 x 1/2” Hair (used on ZM Series 0 Only) (4)
38
9-2017
BOLT, 1/2-20 Shoulder (ZMT, ZM & MZM Series 1 & 2 Models) (4)
39
9-0559
NUT, 1/2-20 Hex Jam (ZMT & ZM Series 1 Models) (2)
40
9-1508
BOLT, 5/16-18 x 3/4” Carriage, Gr. 5 (ZMT & ZM Series 1 & 2 Models) (6)
41
9-0393
NUT, 1/2-20 Hex Nyloc (4)
MID MOUNT Z-RIDER
MANUAL No. 06110