Sebo Airbelt K - Manual (Page 8)

8
To remove a brush or power head, switch off the power and unplug the vacuum. Then,
press the tool release button (7) and pull the tube out.
NOTE! K3 users with ET-H or ET-1 power heads, please refer to your power head user’s
manual for more detailed instructions for operating and maintaining your power head.
Premium Parquet nozzle - Figure 13
The parquet nozzle (29) is specially designed for use on hard surfaces. The brush should be
cleaned regularly. Remove the parquet brush from the telescopic tube to clean. Fibers and
hair can be pulled out of the bristles manually, or vacuum the bristles with with the tele-
scopic tube. The brush strips are removable for cleaning and replacement.
Kombi nozzle - Figure 14
The Kombi nozzle (30) is adjustable for carpet or hard floors. To set for carpet, slide the up
arrow button (42) to the right until it clicks into place. The hard floor dusting brush will raise
up allowing the head to move over the carpet. To set for hard floors, slide the down arrow
button (43) to the left until it clicks into place. The brush will lower to gently sweep your
floors. The slider in Figure 14 is set in the position for hard floors. The brush should be
cleaned regularly. Remove the Kombi nozzle from the telescopic tube to clean. Fibers and
hair can be pulled out of the bristles manually, or vacuum the bristles with with the tele-
scopic tube. The brush strip is removable for cleaning and replacement.
Turbo head - Figure 15
The Turbo head (31) has an air-driven rotating brush for gentle brushing of carpets. The
Turbo head can be adjusted for high and low pile carpet. To adjust the head for high pile car-
pet, push the slider button (44) to the right. For low pile carpet, push the slider button (44)
to the left. The slider in Figure 15 is set in the low pile position. The rotating brush should
be cleaned regularly. Remove the Turbo head from the telescopic tube to clean. Remove
fibers and hair from the brush manually.
The telescopic tube (4) is useful for vacuuming corners and hard-to-reach areas. You may
use the telescopic tube without a brush, power head or attachment. To remove a brush or
power head, switch off the power control knob (9) and unplug the vacuum. Then, press the
tool release button (7) and pull the tube out. The crevice nozzle (20) and dusting brush (28)
may be inserted onto the end of the tube. To use the upholstery nozzle (11), fit it onto the end
of the crevice nozzle (20). It is not necessary to turn off the vacuum while switching the stan-
dard attachments (the crevice nozzle, upholstery nozzle or dusting brush). After use, switch
off the power, unplug the vacuum and remove attachment. Re-insert the telescopic tube into
the power head or brush, turning the tube if needed, until you hear it click into place.
NOTE! K3 users with ET-H or ET-1 power heads, please refer to your power head user’s
manual for more detailed instructions for connecting your power head.
To use the hose without the telescopic tube, switch off the power and unplug the vacuum.
Push the handle release button (3) and pull the HANDLE out of the end of the telescopic tube.
Do not try to separate the hose from the handle! Insert the crevice nozzle (20) or dusting brush
(28) onto the end of the handle. To use the upholstery nozzle (11), fit it onto the end of the
crevice nozzle (20). After use, switch off the power, unplug the vacuum and remove the
attachment. Re-insert the handle into the telescopic tube making sure it is seated correct-
ly and snap it into place.
Figure 11
Figure 12
7
Using the Telescopic Tube, Hose & Attachments - Figures 11 & 12
4
L
R
Figure 13
Figure 15
Figure 14
43
Always unplug vacuum from outlet before dismantling
any part of machine!
!
USE AND MAINTENANCE OF BRUSHES AND HEADS
42
44
▲
▲
20
1
4
20 11
29
30
▲
▲
31