Samsung CLP-310N User Manual
Page 22
22 _Getting started
CONFIGURING WIRELESS NETWORK FROM
SYNCTHRU WEB SERVICE
You must configure the appropriate network parameters to use your printer
in a wireless network. You can use SyncThru™ Web Service, an embedded
web site of your printer. This section gives you basic information on
802.11b/g network parameters which can be configured from the
SyncThru™ Web Service.
You can configure basic wireless settings, such as SSID, Operation Mode
and WPA Shared Key. You can retrieve basic settings by selecting a
wireless network.
If you do not know about your wireless environment, please ask the network
administrator.
1. Enter your machine’s IP address as the URL in a browser and click Go
to access the web site of your machine.
2. Click Network Settings and Wireless.
3. Select Wizard in Wireless Settings.
4. Click Next.
5. Select Network Name(SSID) in SSID Setup.
•
SSID: SSID(Service Set Identifier) is a name that identifies a wireless
network. Access points and wireless devices attempting to connect
to a specific wireless network must use the same SSID. The SSID is
case-sensitive.
•
Operation Mode: Operation Mode refers to the type of wireless
connections.
- Ad-hoc: allows wireless devices to communicate directly with each
other in a peer-to-peer environment.
- Infrastructure: allows wireless devices to communicate with each
other through an access point.
6. Click Next.
If wireless security setting window appears, enter the registered
password and click Next.
•
Operation Mode is Infrastructure:
- None: This is used when the validation of a wireless device’s
identity and data encryption are not required for your network. Open
system is used for IEEE 802.11 authentication.
- Static WEP: This uses the WEP (Wired Equivalent Privacy)
algorithm suggested by IEEE 802.11 standard for security. Static
WEP security mode requires a proper WEP key for data encryption,
decryption, and IEEE 802.11 authentication.
- WPA Personal: You can select WPA-PSK to authenticate the print
server based on WPA Pre-Shared Key. This uses a shared secret
key (generally called Pre Shared Key passphrase) that is manually
configured on the access point and each of its clients. This is
suitable for users who want to use WPA but do not have a RADIUS
server installed on their network.
•
Operation Mode is Ad-hoc:
- None: This is used when the validation of a wireless device’s
identity and data encryption are not required for your network. Open
system is used for IEEE 802.11 authentication.
- Static WEP: This uses the WEP (Wired Equivalent Privacy)
algorithm suggested by IEEE 802.11 standard for security. Static
WEP security mode requires a proper WEP key for data encryption,
decryption, and IEEE 802.11 authentication.
7. Wizard Setup Confirmation window appears, please check your
wireless setup. If the setup is right, click Apply.
8. Click OK.
Contact the network administrator if you are not sure how to configure.
You can also set up the network settings through the network
administration programs.
•
SyncThru™ Web Admin Service: Web-based printer
management solution for network administrators. SyncThru™
Web Admin Service provides you with an efficient way of
managing network devices and lets you remotely monitor and
troubleshoot network machines from any site with corporate
internet access. Download this program from
.
•
SyncThru™ Web Service: Web server embedded on your
network print server, which allows you to:
- Configure the network parameters necessary for the machine to
connect to various network environments.
- Customize machine settings.
•
SetIP: Utility program allowing you to select a network interface
and manually configure the IP addresses for use with the TCP/IP
protocol. (See "Using SetIP program" on page 21.)
CLP-310W, CLP-315W can be used in wireless network
environments. (See "Configuring wireless network from syncthru web
service" on page 22.)
Before wireless network settings, your machine must have an IP
address. See "Using SetIP program" on page 21.
If you want to set wireless network directly, select
Custom
.
If Operation Mode of Network Name(SSID) is Infrastructure, you
must disconnect the network cable to activate wireless network
after completing the network setting.