Sony XR-CA660X User Manual

Fm / am cassette car stereo, Xr-ca660x

Advertising
background image

SONY XR-CA660X (GB,ES,CT) 3-247-838-11 (1)

SONY XR-CA660X (GB,ES,CT) 3-247-838-11 (1)

1

Catch

Cautions

•This unit is designed for negative earth 12 V DC

operation only.

•Do not get the wires under a screw, or caught in

moving parts (e.g. seat railing).

•Before making connections, turn the car ignition

off to avoid short circuits.

•Connect the yellow and red power input leads

only after all other leads have been connected.

Run all earth wires to a common earth point.

•Be sure to insulate any loose unconnected wires

with electrical tape for safety.

Notes on the power supply cord (yellow)
•When connecting this unit in combination with

other stereo components, the connected car

circuit’s rating must be higher than the sum of

each component’s fuse.

•When no car circuits are rated high enough,

connect the unit directly to the battery.

Parts Iist (1)

•The numbers in the list are keyed to those in the

instructions.

•The bracket 1 and the protection collar 5 are

attached to the unit before shipping. Before

mounting the unit, use the release keys 7 to

remove the bracket 1 and the protection collar
5

from the unit. For details, see “Removing the

protection collar and the bracket (4)” on the

reverse side of the sheet.

Keep the release keys 7 for future use as

they are also necessary if you remove the unit
from your car.

Caution

Handle the bracket 1 carefully to avoid injuring

your fingers.

Note
Before installing, make sure that the catches on both
sides of the bracket
1 are bent inwards 2 mm. If the
catches are straight or bent outwards, the unit will not
be installed securely and may spring out.

Connection example (2)

Notes (2-B-

)

• Be sure to connect the earth cord before connecting

the amplifier.

• If you connect an optional power amplifier and do

not use the built-in amplifier, the beep sound will be
deactivated.

Tip (2-B-

)

For connecting two or more CD/MD changers, the
source selector XA-C30 (optional) is necessary.

Connection diagram (3)

1

To a metal surface of the car
First connect the black earth lead, then connect the
yellow and red power input leads.

2

To the power aerial control lead or power supply
lead of aerial booster amplifier
Notes
• It is not necessary to connect this lead if there is

no power aerial or aerial booster, or with a
manually-operated telescopic aerial.

• When your car has a built-in FM/AM aerial in the

rear/side glass, see “Notes on the control and
power supply leads.”

3

To AMP REMOTE IN of an optional power amplifier
This connection is only for amplifiers. Connecting
any other system may damage the unit.

4

To the interface cable of a car telephone

5

To the +12 V power terminal which is energised in
the accessory position of the ignition key switch
Notes
• If there is no accessory position, connect to the

+12 V power (battery) terminal which is energised
at all times.
Be sure to connect the black earth lead to a metal
surface of the car first.

• When your car has a built-in FM/AM aerial in the

rear/side glass, see “Notes on the control and
power supply leads.”

6

To the +12 V power terminal which is energised at
all times
Be sure to connect the black earth lead to a metal
surface of the car first.

Notes on the control and power supply leads
• The power aerial control lead (blue) supplies +12 V

DC when you turn on the tuner.

• When your car has built-in FM/AM aerial in the rear/

side glass, connect the power aerial control lead
(blue) or the accessory power input lead (red) to the
power terminal of the existing aerial booster. For
details, consult your dealer.

• A power aerial without relay box cannot be used

with this unit.

Memory hold connection
When the yellow power input lead is connected,
power will always be supplied to the memory circuit
even when the ignition key is turned off.

Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms, and

with adequate power handling capacities to avoid its
damage.

• Do not connect the speaker terminals to the car

chassis, or connect the terminals of the right speakers
with those of the left speaker.

• Do not connect the earth lead of this unit to the

negative (–) terminal of the speaker.

• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active

speakers (with built-in amplifiers) to the speaker
terminals may damage the unit.

• To avoid a malfunction, do not use the built-in

speaker wires installed in your car if the unit shares a
common negative (–) lead for the right and left
speakers.

• Do not connect the unit’s speaker cords to each

other.

Note on connection
If speaker and amplifier are not connected correctly,
“FAILURE” appears in the display. In this case, make
sure the speaker and amplifier are connected correctly.

3-247-838-11

(1)

Installation/Connections

Instalación/Conexiones

Sony Corporation © 2003

Printed in Thailand

1

1

2

Ч

4

3

4

7

6

5

Ч

2

Equipment used in illustrations (not supplied)
Equipo utilizado en las ilustraciones (no suministrado)

Power amplifier
Amplificador de potencia

CD/MD changer
Cambiador de CD/MD

Front speaker
Altavoces delanteros

Rear speaker
Altavoces traseros

2

B

BUS AUDIO IN

BUS CONTROL IN

A

Rotary commander RM-X4S
Mando rotativo RM-X4S

AUDIO OUT

REAR

FM/AM
Cassette
Car Stereo

XR-CA660X

BUS AUDIO IN

BUS CONTROL IN

Source selector*
Selector de fuente*

*

XA-C30

*

not supplied

no suministrado

Advertising