Symphonic SC724DF - Manual (Page 13)

G [VIEW]
PG [VIEW]
PG–13 [VIEW]
B R [BLOCK]
NC–17 [BLOCK]
X [BLOCK]
CH 15
NO TV SIGNALS
13
EN
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
B CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
CHANGE ACCESS CODE
4
Use the Number buttons to
enter your desired access
code in the "NEW CODE",
then enter the same code in
the "CONFIRM CODE". When
completed, the menu will
return to "V-CHIP SET UP".
5
Press [SET-UP] to exit the menu.
NOTE:
• Your personal access code will be erased and will
return to the default (0000) when a power failure
occurs or when you turn off the power using a wall
switch. If you forget the code, unplug the power cord
for 10 seconds to restore the access code to 0000.
C
NEW CODE
X X X X
CONFIRM CODE
_ _ _ _
– CHANNEL SET UP –
ADD / DELETE CH (CATV)
B AUTO CH PROGRAMMING
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
B CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
– CHANNEL SET UP –
B ADD / DELETE CH (CATV)
AUTO CH PROGRAMMING
ADDING/DELETING CHANNELS
You can add channels that was not memorized due
to the bad reception status and also delete chan-
nels you no longer receive or seldom watch.
1 Press [SET-UP].
Use [K
K / L L ] to point to
"CHANNEL SET UP", then
press [ENTER].
2 Use [K K / L L ] to point to
"ADD/DELETE CH", then
press [ENTER].
3 Use the Number buttons or
[CH. K
K / L L ] to select your
desired channel number.
(You can also use [K
K / L L ] to
enter it.)
• Refer to page 9 on how to use
the Number buttons.
4
Press [ENTER] repeatedly. The channel number
changes to red (deleted) or blue (added) every
time you press the button.
• To delete another channel, repeat steps 3 to 4.
5 Press [SET-UP] to exit the menu.
NOTE:
• To confirm that channel(s) has(have) been deleted
or added, select it (them) using [CH. K K / L L ].
08
ADD / DELETE
(Example: CH8)
MPAA RATING SET UP
4
Use [ K K / L L ] to point to your
desired item, then press
[ENTER] to select "BLOCK"
or "VIEW".
5
Press [SET-UP] to exit the menu.
Selection Rating Category Explanations
G
General Audience
PG Parental Guidance suggested.
PG-13 Unsuitable for children under 13
R Restricted; under 17 requires acco-
mpanying parent or adult guardian
NC-17 No one under 17 admitted
X Mature audience only
B
CHANNEL SET UP
Channel presetting is necessary at the start or in case you moved the TV to a different area.
TV OPERA
TION AND SETTINGS
TV/VCR SECTION
TV/VCR TV/VCR
<EXAMPLE>
AUTO CHANNEL PROGRAMMING
1
Press [SET-UP].
Use [K K / L L ] to point to
"CHANNEL SET UP", then
press [ENTER].
2 Use [K K / L L ] to point to "AUTO
CH PROGRAMMING", then
press [ENTER].
The tuner scans and memorizes all the active
channels in your area.
3
When the scanning is comple-
ted, the lowest memorized
channel is displayed.
If "NO TV SIGNALS" appears
on the TV screen, check the
antenna connection and try
again.
NOTES:
• The unit may recognize CATV channels to be TV
channels if reception condition is poor. In this case,
check the antenna connection and try "AUTO CH
PROGRAMMING" again.
• Auto channel programming is NOT necessary
when connected to a cable box or satellite box.
Just select the channel for cable box or satellite
input (ex. CH3 or CH4) on the unit, then select
your desired channel on the cable box or satellite
box.
T2203UD_EN.QX4 06.4.11 7:19 PM Page 13