Skylink 18KR - Manual (Page 2)

If, within one year from date of purchase, this product should become defective
(except battery), due to faulty workmanship or materials, it will be repaired or
replaced, without charge. Proof of purchase and a Return Authorization are required.
13. WARRANTY
6. KEYPAD OPERATION
9. ADDITIONAL TRANSMITTER
11. CAUTION
12. FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference
received, including interference that may cause undesired operation.
WARNING:
Changes or modifications to this unit not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The backlight comes on and a beep is emitted when any key is pressed.
The backlight of the keypad may not be visible when it is too bright
outside. When any key is pressed, the next key must be pressed w ithin 5
seconds or the backlight turns off and the sequence is cancelled. You
must begin again.
If the keypad does not emit a beep when pressed, wait a few seconds
and press the key again.
7. CHANGE PIN
Follow the instructions below to change the PIN.
To change your PIN:
1. Enter the current PIN, (factory default PIN 0 0 0 0), press ,
2. Enter new 4 to 6 digit PIN, press ,
3. Enter new PIN again, press .
For example, if you are changing the PIN number from 0000 to
123456, enter the following sequence, 0000, ,123456, ,123456, .
If confirmed, the backlit LED flashes and the unit emits a long beep.
*
* * *
If you do not hear 3 beeps after the 4-digit PIN, [#] and [assigned door
number] is entered, that means you have entered an incorrect PIN, and
the keypad transmitter will not operate your garage door.
*
*
Two 3 volt Lithium type (CR2032) batteries (included).
It is time to change
the batteries when
the backlight no
longer appears.
+
-
Battery Compartment
8. BATTERY
RISK OF ELECTRICAL SHOCK. FOR INDOOR USE ONLY.
CAUTION : DISCONNECT POWER BEFORE SERVICING.
Maximum Rating:
Input : 120VAC 60Hz 2W
14. CUSTOMER SERVICE
CUSTOMER SERVICE
17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3
Email:[email protected]
http://www.skylinkhome.com
P/N. 101A288-001 Rev.1
©2004 SKYLINK GROUP
If you would like to order Skylink’s products or have difficulty getting them to work,
please :
1. visit our FAQ website at www.skylinkhome.com , or
2. email us at [email protected] , or
3. call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST.
Fax +800 286-1320
You can add up to 15 transmitters as you want to
control the same receiver. Simply program the
transmitters to the receiver. Skylink
® offers Keychain
Transmitter Model 18T4 and Keyless Entry Transmitter
Model 18K to work with your receiver.
For more information, please visit our website at
www.skylinkhome.com or contact us.
10. ADDITIONAL RECEIVER
You can use 18K to control up to 4 garage door openers by adding
Skylink
® Garage Door Receiver 18R for each opener.
5. REMOVE TRANSMITTER FROM THE RECEIVER
4. PROGRAM A KEYPAD TO THE RECEIVER (CONT)
Press the [4-digit PIN], [#] and [the assigned
number of the door] within 5 seconds. The
assigned door number can be either 1, 2, 3 or 4.
Example: [0][0][0][0][#][3], for door 3.
The receiver red LED will go off indicates the
programming is completed.
To program the keypad to control more than
one receiver, repeat process (1) to (4) with
different assigned door numbers.
3
4
5
Learn Button
You can delete the transmitter from a receiver.
Unplug the receiver from the electrical socket.
Press and hold the learn button on the left hand side of the receiver
when plugging the receiver into an electrical socket, the red LED on the
receiver will flash rapidly. All the transmitters and keypads are deleted. 2
1