Sharp Aquos LC 20S5U - Manual (Page 16)

14
Press POWER on the upper side of the main unit, to
turn on the TV. The SELECT LANGUAGE screen will
be displayed.
Press '/" to select “ENGLISH”, “ESPAÑOL”
(Spanish) or “FRANÇAIS” (French).
E N G L I S H
E S P A Ñ O L
F R A N Ç A I S
Press ENTER to access CH SEARCH mode.
Press '/" to select “ON” or “OFF”. When you select
“ON”, the LCD TV set will automatically memorize the
broadcasting channels.
O N
O F F
A
• If you select “OFF”, EZ SETUP will be canceled.
Press ENTER to access AUTO CLOCK mode.
Press '/" to select “ON” or “OFF”.
When you select “ON”, the LCD TV set will
automatically adjust the clock to search time-signals
(EDS signals), which are provided by some TV
stations. The AUTO CLOCK setting may take from
several minutes to an hour depending on the number of
channels to receive and signal status. If you know the
channel of the EDS signal carrier (PBS or other) in your
area, select “OFF” and follow the procedure in AUTO
CLOCK Setting. (See page 15.)
O N
O F F
EZ SETUP (With AUTO CLOCK Setting)
EZ SETUP during the First Power On
■ When you turn on the LCD TV set for the first time, it will
automatically memorize the broadcasting channels and
clock.
Please perform the following instructions before you press
POWER.
(1) Insert the batteries into the remote control. (See page 7.)
(2) Connect the antenna cable to the LCD TV set. (See page 8.)
(3) Connect the AC cord to the AC INPUT terminal of the
LCD TV set and plug in the AC cord to the wall outlet.
(See page 9.)
1
2
Press ENTER to access START EZ SETUP mode.
Press '/" to select “YES”, and press ENTER.
A
• If you want to stop the EZ SETUP process once it has
started, press MENU and it will be canceled. If you want to
set up again, please refer to CH SETUP on page 24.
Y E S
N O
C O N N E C T A N T E N N A
O R C A B L E .
The tuner will automatically search for the broadcasting
and cable TV channels. (The channel number will
automatically increase when it appears.)
� P L E A S E � W A I T � � � � �
� �
� A U T O � P R O G R A M M I N G
� �
� � � � �
� �
� � �
� �
The LCD TV set will automatically switch to searching
for EDS signals.
If EDS signals are received, the channel number and
time will be displayed, and then the screen shown in
step 5 appears.
�
� P L E A S E � W A I T � � � � �
� �
� N O W � S E A R C H I N G � T I M E �
� �
� � � � �
� �
� � �
� �
Once EZ SETUP is completed, the lowest channel
number memorized will be displayed.
S T E R E O
S A P
M O N O � � � � � � � � � � � � � � � � � � � 1 1 : 5 3 A M
2
A
• Do not let the EZ SETUP screen remain unattended for a long time.
• If EZ SETUP does not memorize all the channels in your region,
please refer to page 24 for more information on manually
memorizing the channels using CH SETUP.
• It may be difficult to preset when the broadcasting signals are
weak, the channel cycle frequency is incorrect or the frequency
jamming is occurring around the area. Please refer to page 24
for more information on manually memorizing channels using
CH SETUP.
• If there are no channels with EDS signals or the antenna signal
is weak, the AUTO CLOCK setting may not operate. In this case,
the “EDS CH IS NOT AVAILABLE.” message will appear and the
mode will change to MANUAL CLOCK setting. Refer to page 15
to set the clock manually.
4
5
3
POWER
LC-20S5U_E.indb 14 2005/12/15 11:18:53