Samsung CLX-6220 - Manual (Page 34)

Network setup_ 3
3.Click the Firewall menu.
4.Turn the firewall off.
The following instructions may vary for your model.
Perform the following to configure the IP address:
1.Connect your machine and the computer using network cable.
2.Insert the Installation CD-ROM, and open the disk window. Open the
MAC_Installer > MAC_Printer > SetIP > SetIPApplet.html.
3.Double click the file and Safari will automatically open, then select
Trust. The browser will open the SetIPApplet.html page that shows
the printer’s name and IP address information.
4.Click on the icon (third from left) in the SetIP window to open the
TCP/IP configuration window.
5.Enter the printer’s new information into the configuration window as
follows. In a corporate intranet, you may need to have this
information assigned by a network manager before proceeding.
• MAC Address: Find the machine’s MAC address from the Network
Configuration Report and enter it without the colons. For
example, 00:15:99:29:51:A8 becomes 0015992951A8.
The MAC address is the hardware serial number of the
on-board network interface and can be found on the
Network Configuration Report.
• IP Address: Enter a new IP address for your printer.
For example, if your computer’s IP address is 192.168.1.150,
enter 192.168.1.X. (X is number between 1 and 254 other than
the computer’s address.)
• Subnet Mask: Enter a new Subnet Mask for your machine.
• Default Gateway: Enter a new Gateway for your machine.
6.Select Apply, then OK, and OK again. The printer will automatically
print the configuration report. Confirm that all of the settings are
correct. Quit Safari. You may close and eject the installation
CD-ROM. If necessary, restart the computer’s firewall. You have
successfully changed the IP address, subnet mask, and gateway.
IPv4 setting using SetIP Program (Linux)
The SetIP program should be automatically installed during the printer
driver installation.
The path and UIs may differ by Linux OS version. Refer to the
Linux OS manual to turn firewall off.
1.Print the machine’s network configuration report to find your machine’s
MAC address.
2.Open the /opt/Samsung/mfp/share/utils/.
3.Double click the SetIPApplet.html file.
4.Click to open the TCP/IP configuration window.
5.Enter the MAC address, IP address, subnet mask, default gateway,
and then click Apply.
When you enter the MAC address, enter it without a colon(:).
6.The machine prints the network information. Confirm all of the settings
are correct.
7.Close the SetIP program.
Network parameter setting
You can also set up the various network settings through the network
administration programs such as SyncThru™ Web Admin Service and
SyncThru™ Web Service.
Restoring factory default settings using SyncThru™
Web Service
1.Start a web browser such as Internet Explorer, Safari or Firefox and
enter your machine’s new IP address in the browser window.
For example,
2.Click Go to access the SyncThru™ Web Service.
3.Click Login on the upper right of the SyncThru™ Web Service
website.
A log-in page appears.
4.Type in the ID and Password then click Login .
If it’s your first time logging into SyncThru™ Web Service, type in the
below default ID and password.
• ID: admin
• Password: sec00000
5.When the SyncThru™ Web Service window opens, click Settings >
Network Settings > Restore Default.
6.Click Clear for network.
7.Turn off and restart machine to apply settings.
Installing network connected machine’s driver
You must install the printer driver software for printing. The software
includes drivers, applications, and other user friendly programs.
Make sure that the network setup for your machine is completed. All
applications should be closed on your computer before beginning
installation.
Windows
This is recommended for most users. All components necessary for
machine operations will be installed.
Follow the steps below:
1. Make sure that the machine is connected to the network and powered
on.
2. Insert the supplied software CD into your CD-ROM drive.
• The software CD should automatically run and an installation window
appear.
• If the installation window does not appear, click Start and then Run.
Type X:\Setup.exe, replacing “X” with the letter which represents
your CD-ROM drive. Click OK.
• If you use Windows Vista, Windows 7 and Windows 2008 Server R2,
click Start > All programs > Accessories > Run.
Type X:\Setup.exe replacing “X” with the letter which represents
your CD-ROM drive and click OK.
• If the AutoPlay window appears in Windows Vista, Windows 7 and
Windows 2008 Server R2, click Run Setup.exe in Install or run
program field, and click Continue or Yes in the User Account
Control windows.