Sony CMT-LX40I - Manual (Page 2)

CMT-LX40i/LX20i.GB.4-131-630-13(1)
Playing the iPod
1 Select the iPod function.
Press FUNCTION +/  repeatedly.
2 Place the iPod.
3 Start playback.
Press  (or  on the unit) .
To control the iPod
You can control your iPod with the following buttons on
the remote or unit.
To Press
Pause playback  (pause) (or  (play/pause)
on the unit)  or  (stop) .
Scroll up/down the
iPod menus
 / . You can scroll up or
down the iPod menus much like
the Click Wheel operations of
the iPod or the drag up-or-down
operations of the iPod touch.
Select a track
or chapter of
audiobook/podcast
/ (go back/go forward)
. To fast-forward or fast-
rewind, hold down the button.
Choose the selected
item
 / (enter) (or ENTER on
the unit) . You can choose the
selected item much like the center
button on the iPod or the touch
operation of the iPod touch.
Find a point in a
track or chapter of
audiobook/podcast
Hold down / (rewind/
fast forward)  during playback,
and release the button at the
desired point.
Return to the
previous menu or
select a menu
 /TOOL MENU /
(return) . You can return to the
previous menu or select a menu
much like the Menu button on
the iPod or the touch operation
of the iPod touch.
To use the system as a battery charger
You can use the system as a battery charger for the iPod
when the system is on.
The charging begins when the iPod is placed on the
unit’s connector. The charging status appears in the iPod
display. For details, see the user’s guide of your iPod.
To stop charging the iPod
Remove the iPod.
Notes
 When placing or removing the iPod, handle the iPod in the same
angle as that of the iPod connector on the unit and do not twist or
sway the iPod to prevent connector damage.
 Do not carry the unit with an iPod set on the connector. Doing so
may cause a malfunction.
 When placing or removing the iPod, brace the unit with one hand
and take care not to press the controls of the iPod by mistake.
 Before disconnecting the iPod, pause playback.
 While playing video, you cannot use / . You can fast
rewind (fast forward) by holding down / .
 To change the volume level, use VOLUME +/ . The volume level
does not change even if adjusted on the iPod.
 This system is designed for iPod only. You cannot connect any other
portable audio players.
 To use an iPod, refer to the user’s guide of your iPod.
 Sony cannot accept responsibility in the event that data recorded to
iPod is lost or damaged when using an iPod with this system.
Creating your own program
(Program Play)
Use buttons on the remote to create your own program.
1 Select the CD function.
Press FUNCTION +/  repeatedly.
2 Select the play mode.
Press PLAY MODE  repeatedly until “PGM”
appears while the player is stopped.
3 Select the desired track or file number.
Press /  repeatedly until the desired track
or file number appears.
When programming MP3 files, press +/ 
repeatedly to select the desired folder, and then select
the desired file.
Selected track or file number
Total playing time of the
selected track or file
4 Program the selected track or file.
Press  to enter the selected track or file.
5 Repeat steps 3 through 4 to program additional
tracks or files, up to a total of 25 tracks or files.
6 To play your program of tracks or files, press  .
The program remains available until you remove the
disc. To play the same program again, select the CD
function, and then press  .
To cancel Program Play
Press PLAY MODE  repeatedly until “PGM”
disappears while the player is stopped.
To delete the last track or file of the program
Press CLEAR  while the player is stopped.
To view program information, such as total
track number of the program
Press DISPLAY  repeatedly.
Using optional audio components
1 Prepare the sound source.
Connect additional audio component to the AUDIO
IN jack  on the unit using an audio analog cord
(not supplied).
2 Turn down the volume.
Press VOLUME  .
3 Select the AUDIO IN function.
Press FUNCTION +/  repeatedly.
4 Start playback.
Start playback of the connected component and adjust
its volume.
5 Adjust the volume.
Press VOLUME +/ .
Adjusting the sound
To Press
Generate a more dynamic
sound (Dynamic Sound
Generator X-tra)
DSGX  on the unit.
Set the sound effect EQ .
Changing the display
To Press
Change
information on the
display 1)
DISPLAY  repeatedly when the
system is on.
Check the clock
when the system
is off.
DISPLAY  when the system is
off 2) . The clock is displayed for 8
seconds.
1) For example, you can view CD/MP3 disc information, such as;
 track or file number during normal play.
 track or file name (“ ”) during normal play.
 artist name (“ ”) during normal play.
 album or folder name (“ ”) during normal play.
 total playing time while the player is stopped.
 volume label if it exists on the disc.
You can also view DAB station information (CMT-LX40i only) such
as the service name, channel label, preset number, frequency, DLS
(Dynamic Label Segment), or ensemble label.
2) The STANDBY indicator  on the unit lights up when the system is
off.
Notes on the display information
 Characters that cannot be displayed appear as “_”.
 The following are not displayed;
 total playing time for an MP3 disc.
 remaining playing time for an MP3 file.
 The following are not displayed correctly;
 elapsed playing time of an MP3 file encoded using VBR (variable
bit rate).
 folder and file names that do not follow either the ISO9660
Level 1, Level 2 or Joliet in the expansion format.
 The following are displayed;
 total playing time for a CD-DA disc during normal play.
 remaining playing time for a track.
 remaining playing time of a current CD-DA disc during normal
play.
 ID3 tag information for MP3 files when ID3 version 1 and
version 2 tags are used (ID3 version 2 tag information display has
priority when both ID3 version 1 and version 2 tags are used for a
single MP3 file).
 up to 15 characters of ID3 tag information using uppercase letters
(A to Z), numbers (0 to 9), and symbols (" $ % ’ ( ) * + , – . / < = >
@ [ \ ] _ ` { | } ! ? ^).
Note on the DAB display information (CMT-LX40i only)
The following is also displayed;
 up to 8 characters of service name, up to 128 characters of DLS
(Dynamic Label Segment) and up to 16 characters of ensemble
label using uppercase letters (A to Z), numbers (0 to 9), and
symbols (" $ % ’ ( ) * + , – . / < = > @ [ \ ] _ ` { | } ! ? ^).
Using the timers
The system offers two timer functions. If you use both
timers, the Sleep Timer has priority.
Sleep Timer:
You can fall asleep to music. This function works even if
the clock is not set.
Press SLEEP  repeatedly. If you select “AUTO,” the
system automatically turns off after the current disc stops
or in 100 minutes.
Play Timer:
You can wake up to CD, tuner or iPod at a preset time.
Make sure you have set the clock.
Use buttons on the remote to use the Play Timer
functions.
1 Prepare the sound source.
Prepare the sound source, and then press VOLUME
+/  to adjust the volume.
To start from a specific CD track or audio file, create
your own program.
2 Select the timer set mode.
Press TIMER MENU .
3 Set the play timer.
Press /  repeatedly to select “PLAY SET,” then
press .
“ON TIME” appears, and the hour indication flashes.
4 Set the time to start playback.
Press /  repeatedly to set the hour, then press
.
The minute indication flashes. Use the procedure
above to set the minutes. “OFF TIME” appears and the
hour indication flashes in the display.
5 Use the same procedure as in step 4 to set the time
to stop playback.
6 Select the sound source.
Press /  repeatedly until the desired sound
source appears, then press . The display shows
the timer settings.
7 Turn off the system.
Press  . The system turns on 15 seconds before
the preset time.
If the system is on at the preset time, the Play Timer
will not play. Do not operate the system from the time
the system turns on until the playback starts.
To check the setting
1
Press TIMER MENU .
“SELECT” flashes in the display.
2 Press .
3 Press /  repeatedly to select “PLAY SEL,” then
press .
To cancel the timer
Repeat the same procedure as above until “OFF” appears
in step 3, and then press .
To change the setting
Start over from step 1.
Notes for the iPod user
 Make sure the iPod is not playing when using the Play Timer.
 The Play Timer may not be activated depending on the status of the
connected iPod.
Tip
The Play Timer setting remains as long as the setting is not cancelled
manually.
iPod
There is no sound.
 Make sure the iPod is connected securely.
 Make sure the iPod is playing music.
 Adjust the volume.
The sound is distorted.
 Turn down the volume.
 Set the “EQ” setting of the iPod to “Off” or “Flat.”
The remote does not function.
 Make sure the iPod is updated with the latest software.
If not, update the iPod before using with the system.
The iPod cannot be charged.
 Make sure the iPod is connected securely.
 You can use the system as a battery charger for iPod
only when the system is on.
“OVER CURRENT” appears.
 A problem has been detected with the level of electrical
current from the iPod connector. Turn off the system
and remove the iPod from the iPod connector. Make
sure there is no problem with the iPod. If this display
pattern persistes, contact your nearest Sony dealer.
To change the AM tuning interval
(CMT-LX20i only)
The AM tuning interval is factory-preset to 9 kHz (or
10 kHz for some areas).
Use buttons on the unit to change the AM tuning
interval.
1 Tune in any AM station, and then turn off the
system.
2 Press DISPLAY  to display the clock.
3 While holding down  , press  .
All the AM preset stations are erased. To reset the
interval to the factory preset, repeat the procedure.
To improve disc loading performance
Turn on the CD player power using the CD power
management function. By default, the CD player power
is turned off.
Use buttons on the unit to turn on the CD player power.
1 Press FUNCTION +/  repeatedly to select the CD
function.
2 Press   to turn off the system.
3 After “STANDBY” stops flashing, press DISPLAY 
to display the clock and then press   while
holding down  .
“CD POWER ON” appears. Turning the CD player
power on, decreases disc access time and improves
loading performance.
If there is poor tuner reception when the CD player
power is turned on, return the setting to default. To
turn off the CD player power, repeat the procedure
until “CD POWER OFF” appears.
To reset the system to factory settings
If the system still does not operate properly, reset the
system to factory settings.
Use buttons on the unit to reset the unit to its factory
default settings.
1 Disconnect and reconnect the power cord, and then
turn on the system.
2 Hold down   and ENTER , and press  .
All user-configured settings, such as preset radio
stations, timer, and the clock, are deleted.
Messages
COMPLETE: The preset operation ended normally.
FULL: You tried to program more than 25 tracks or files
(steps).
LOCKED: The system does not eject the disc. Contact
your nearest Sony dealer.
NO DISC: There is no disc in the player, or you have
loaded a disc that cannot be played.
NoPRESET (DAB only): There is no stored preset station.
NO SERV (DAB only): There is no supported DAB
broadcast in your country or region.
NO STEP: All of the programmed tracks have been
erased.
No TEXT (DAB only): There is no text information in the
received service.
NOT USED: You pressed an invalid button.
OVER: You have reached the end of the disc while
pressing   during playback or pause.
PUSH STOP: You pressed PLAY MODE  during
playback.
READING: The system is reading information from the
disc. Some buttons are not available.
TIME NG: The Play Timer start and end times are set to
the same time.
Display examples
Display indicates
2 (two)
5 (five)
6 (six)
8 (eight)
0 (zero)
A
B
D
G
H
K
M
O
Q
R
S
Z
! or |
”
$
%
,
.
?
@
^
Precautions
Discs that this system CAN play
 Audio CD
 CD-R/CD-RW (audio data/MP3 files)
Discs that this system CANNOT play
 CD-ROM
 CD-R/CD-RW other than those recorded in music CD
format or MP3 format conforming to ISO9660 Level
1/Level 2, Joliet
 CD-R/CD-RW recorded in multisession that have not
ended by “closing the session”
 CD-R/CD-RW of poor recording quality, CD-R/
CD-RW that have scratches or are dirty, or CD-R/CD-
RW recorded with an incompatible recording device
 CD-R/CD-RW which is finalized incorrectly
 Discs containing files other than MPEG 1 Audio Layer-
3 (MP3) files
 Discs of non-standard shape (for example, heart,
square, star)
 Discs that have adhesive tape, paper, or sticker attached
to them
 Rental or used discs with attached seals where the glue
extends beyond the seal
 Discs that have labels printed using ink that feels tacky
when touched
Notes on discs
 Before playing, wipe the disc with a cleaning cloth from
the center out to the edge.
 Do not clean discs with solvents, such as benzine
thinner, or commercially available cleaners or anti-
static spray intended for vinyl LPs.
 Do not expose discs to direct sunlight or heat sources
such as hot air ducts, nor leave it in a car parked in
direct sunlight.
On safety
 Completely disconnect the power cord (mains lead)
from the wall outlet (mains) if it is not going to be used
for an extended period of time. When unplugging the
unit, always grip the plug. Never pull the cord itself.
 Should any solid object or liquid get into the system,
unplug the system, and have it checked by qualified
personnel before operating it again.
 AC power cord must be changed only at a qualified
service shop.
On placement
 Do not place the system in an inclined position or in
locations that are extremely hot, cold, dusty, dirty, or
humid or lacking adequate ventilation, or subject to
vibration, direct sunlight or a bright light.
 Be careful when placing the unit or speakers on
surfaces that have been specially treated (for example,
with wax, oil, polish) as staining or discoloration of the
surface may result.
 If the system is brought directly from a cold to a warm
location or is placed in a very damp room, moisture
may condense on the lens inside the CD player, and
cause the system to malfunction. In this situation,
remove the disc, and leave the system turned on for
about an hour until the moisture evaporates.
On heat buildup
 Heat buildup on the unit during operation is normal
and is not cause for alarm.
 Do not touch the cabinet if it has been used
continuously at a high volume because the cabinet may
have become hot.
 Do not obstruct the ventilation holes.
On the speaker system
This speaker system is not magnetically shielded, and
the picture on nearby TV sets may become magnetically
distorted. In this situation, turn off the TV, wait 15 to 30
minutes, and turn it back on.
If there is no improvement, move the speakers far away
from the TV.
Cleaning the cabinet
Clean this system with a soft cloth slightly moistened
with a mild detergent solution. Do not use any type
of abrasive pad, scouring powder, or solvent, such as
thinner, benzine, or alcohol.
Specifications
Main unit
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL HARMONIC DISTORTION:
(CMT-LX20i The United States model only)
With 4 ohm loads, both channels driven, from 120  10,000 Hz; rated 25 watts
per channel minimum RMS power, with no more than 10% total harmonic
distortion from 250 milliwatts to rated output.
Amplifier section
CMT-LX40i
DIN power output (rated):
4 + 4 watts (4 ohms at 1 kHz, DIN)
Continuous RMS power output (reference): 5 + 5 watts (4 ohms at 1 kHz,
10% THD)
Music power output (reference): 9 + 9 watts
CMT-LX20i
DIN power output (rated):
4 + 4 watts (4 ohms at 1 kHz, DIN)
Continuous RMS power output (reference): 5 + 5 watts (4 ohms at 1 kHz,
10% THD)
Inputs
AUDIO IN (stereo mini jack): Voltage 775 mV, impedance 22 kilohms
Outputs
PHONES (stereo mini jack): accepts headphones with an impedance of 8 ohms or more
SPEAKER: accepts impedance of 4 ohms
CD player section
System: Compact disc and digital audio system
Laser Diode Properties
Emission Duration: Continuous
Laser Output*: Less than 44.6µW
* This output is the value measurement at a distance of 200mm from the
objective lens surface on the Optical Pick-up Block with 7mm aperture.
Frequency response: 20 Hz  20 kHz
Signal-to-noise ratio: More than 90 dB
Dynamic range: More than 90 dB
Tuner section
DAB tuner section (CMT -LX40i only):
Frequency range*
Band-III: 174.928 (5A)  239.200 (13F) MHz
* For details, see “DAB frequency table” below.
Antenna: DAB lead antenna
Antenna terminal: 75 ohms, F female
DAB frequency table (Band-III)
Frequency Label Frequency Label
174.928 MHz 5A 209.936 MHz 10A
176.640 MHz 5B 211.648 MHz 10B
178.352 MHz 5C 213.360 MHz 10C
180.064 MHz 5D 215.072 MHz 10D
181.936 MHz 6A 216.928 MHz 11A
183.648 MHz 6B 218.640 MHz 11B
185.360 MHz 6C 220.352 MHz 11C
187.072 MHz 6D 222.064 MHz 11D
188.928 MHz 7A 223.936 MHz 12A
190.640 MHz 7B 225.648 MHz 12B
192.352 MHz 7C 227.360 MHz 12C
194.064 MHz 7D 229.072 MHz 12D
195.936 MHz 8A 230.784 MHz 13A
197.648 MHz 8B 232.496 MHz 13B
199.360 MHz 8C 234.208 MHz 13C
201.072 MHz 8D 235.776 MHz 13D
202.928 MHz 9A 237.488 MHz 13E
204.640 MHz 9B 239.200 MHz 13F
206.352 MHz 9C
208.064 MHz 9D
* Frequencies are displayed to two decimal places on this system.
FM stereo, FM/AM superheterodyne tuner
FM tuner section:
Tuning range:
CMT-LX40i: 87.5  108.0 MHz (50 kHz step)
CMT-LX20i: 87.5  108.0 MHz (100 kHz step)
Antenna: FM lead antenna
Intermediate frequency: 10.7 MHz
AM tuner section:
Tuning range:
CMT-LX40i:
531  1,602 kHz (9 kHz step)
CMT-LX20i:
530  1,710 kHz (10 kHz step)
531  1,710 kHz (9 kHz step)
Antenna: AM loop antenna
Intermediate frequency: 450 kHz
iPod section
Compatible iPod models:
iPod touch 2nd
generation
iPod nano 4th
generation
(video)
iPod touch 1st
generation
iPod nano 3rd
generation
(video) iPod classic iPod nano 2nd
generation
(aluminum)
iPod 5th
generation
(video)
iPod nano 1st
generation iPod 4th
generation
(color display)
iPod 4th
generation
iPod mini
Speaker
Speaker system: Full-range, bass-reflex, 80 mm, cone type
Rated impedance: 4 ohms
Dimensions (w/h/d): Approx. 130 Ч 221 Ч 135 mm
Mass: Approx. 0.7 kg net per speaker
General
Power requirements:
CMT-LX40i: 230 V AC, 50/60 Hz
CMT-LX20i: 120 V AC, 60 Hz
Power consumption: 25 watts
Dimensions (w/h/d) (excl. speakers): Approx. 200 Ч 221 Ч 205 mm
Mass (excl. speakers): Approx. 2.2 kg
Supplied accessories: Remote Commander (1), R6 (Size AA) batteries (2)
(CMT-LX40i only), FM lead/AM loop antenna (1), DAB lead antenna (1)
(CMT-LX40i only)
Design and specifications are subject to change without notice.
Halogenated flame retardants are not used in the certain printed wiring
boards.
Troubleshooting
1 Make sure the power cord and speaker cords are
correctly and firmly connected.
2 Find your problem in the checklist below, and take
the indicated corrective action.
If the issue persists, contact your nearest Sony dealer.
If the STANDBY indicator flashes
Immediately unplug the power cord, and check the
following items.
 If your system has a voltage selector, is the voltage
selector set to the correct voltage?
 Are you using only the supplied speakers?
 Is anything blocking the ventilation holes on the top
or back of the system?
 Is the iPod connector short-circuited?
After the STANDBY indicator  stops flashing,
reconnect the power cord, and turn on the system. If
the issue persists, contact your nearest Sony dealer.
General
The system does not turn on.
 Is the power cord plugged in?
There is no sound.
 Are the + and  speaker cords short-circuited?
 Are you using only the supplied speakers?
 Is anything blocking the ventilation holes on the top or
back of the system?
 The specified station may have temporarily stopped
broadcast.
The STANDBY indicator  remains lit after
unplugging the power cord.
 The STANDBY indicator  may not turn off
immediately after unplugging the power cord. This
is not a malfunction. The indicator will turn off after
about 40 seconds.
Sound comes from one channel, or the left and
right volumes are unbalanced.
 Place the speakers as symmetrically as possible.
 Connect only the supplied speakers.
Severe hum or noise.
 Move the system away from sources of noise.
 Connect the system to a different wall outlet.
 Install a noise filter (available separately) to the power
cord.
The remote does not function.
 Remove any obstacles between the remote and the
remote sensor  on the unit, and position the unit
away from fluorescent lights.
 Point the remote at the system’s sensor.
 Move the remote closer to the system.
CD/MP3 player
The sound skips, or the disc will not play.
 Wipe the disc clean, and replace it.
 Move the system to a location away from vibration (for
example, on top of a stable stand).
 Move the speakers away from the system, or place them
on separate stands. At high volume, speaker vibration
may cause the sound to skip.
Play does not start from the first track.
 Return to Normal Play by pressing PLAY MODE 
repeatedly until both “PGM” and “SHUF” disappear.
Starting playback takes more time than usual.
 The following discs can increase the time it takes to start
playback:
 a disc recorded with a complicated tree structure.
 a disc recorded in multisession mode.
 a disc that has not been finalized (a disc to which data
can be added).
 a disc that has many folders.
The system does not eject the disc and
“LOCKED” appears.
 Contact your Sony dealer or local authorized Sony
service facility.
Tuner
Severe hum or noise, or stations cannot be
received. (“TUNED” or “STEREO” flashes on the
display.)
 Connect the antenna properly.
 Find a location and an orientation that provide good
reception, and then set up the antenna again.
 Keep the antennas away from the speaker cords and the
power cord to avoid picking up noise.
 Turn off nearby electrical equipment.
“TUNED” does not appear in the display (DAB
only).
 Check all antenna connections, then perform the DAB
Automatic Scan procedure (see “Reception of DAB
radio station (CMT-LX40i only)”).
 The current DAB service may not be available. Press
+/ (or TUNE +/ on the unit)  to select a different
service.
 If you have moved to another area, some services/
frequencies may have changed and you may not be able
to tune into your usual broadcast.
Perform the DAB Automatic Scan procedure to
re-register the contents of broadcasts. (Performing this
procedure clears all previously stored presets.)