Sim2 Multimedia Grand Cinema Line RTX55H - Manual (Page 10)

SIM2 RTX 55H
RS-232C CONTROL SPECIFICATIONS
10
RECALL
BE EF 03 19 00 85 EB 01 27 09 00 00 01 00 00 00
01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
SAVE CURRENT
SETTINGS BE EF 03 19 00 54 D6 01 27 09 00 00 00 00 00 00
01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
MEMORY 1
SAVE INITIAL
SETTINGS BE EF 03 19 00 45 9A 01 28 09 00 00 01 00 00 00
01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
RECALL
BE EF 03 19 00 74 AB 01 27 09 00 00 01 00 00 00
02 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
SAVE CURRENT
SETTINGS
BE EF 03 19 00 A5 96 01 27 09 00 00 00 00 00 00
02 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
MEMORY 2
SAVE INITIAL
SETTINGS
BE EF 03 19 00 76 DE 01 28 09 00 00 02 00 00 00
01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
RECALL
BE EF 03 19 00 E4 6A 01 27 09 00 00 01 00 00 00
03 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
SAVE CURRENT
SETTINGS
BE EF 03 19 00 35 57 01 27 09 00 00 00 00 00 00
03 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
MEMORY 3
SAVE INITIAL
SETTINGS
BE EF 03 19 00 A7 E3 01 28 09 00 00 03 00 00 00
01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
5. Examples
1. Send the simulated "SWITCH ON FROM STAND-BY AND SELECT SOURCE" Remote Control
keycode.
Remote Control allows Switching on from Stand-by via one of the keys "1", "2" ... "11", "12".
Send, for instance, the code relative to key "1": BEEF02060080E5490100000000.
The projector switches on and selects Input 1.
The projector returns the response code: 06 (Acknowledged with no error).
NOTE: Commands that simulate keys "1", "2" ... "11", "12" switch on the unit and select the
corresponding Source.
Command that simulate key 0 switches on the unit: the last source memorised prior to switch off is
automatically selected.
2. Send the simulated "MENU RIGHT" Remote Control keycode.
Send the packet: BEEF02060023E75A0100000000.
The OnScreen Display appers on the screen.
The projector returns the response code: 06 (Acknowledged with no error).
3. Send the "SET ASPECT ANAMORPHIC" Operation Code.
Send the packet: BEEF0206009DF5840100000000.
The Aspect Ratio changes to Anamorphic.
The projector returns the response code: 06 (Acknowledged with no error).
4. Select "INPUT 5 (COMP RGB 1) WITH YcrCb 15kHz SIGNAL"
Send the packet: BEEF0319005B0C01820800000000000008000000000000000000000000000000
Wait for the return code and add an additional delay of 40 ms.
Send the the code relative to the Key to which Input 5 has been assigned: for instance if the key is "3"
the code is: BEEF02060062E44B0100000000
6. Warnings
When the number of bytes sent to the Projector is greater than indicated for the Command (32 bytes for
Operation Packets and 13 bytes for Event Packets), excess data will be ignored.