Samson Resolv 65a RESOLV65A - Manual (Page 13)

11
ENGLISH
10 Inch Long Throw Transducer 120 Watt Amplifier
10000. 10000.0 1000. 1000.0 100. 100.0
mSec
SPECTRAL DECAY SPECTRAL DECA SPECTRAL DECA
AUDIO
INPUTS
LINE
MADE IN CHINA DESIGNED AND ENGINEERED IN THE UNITED STAT DESIGNED AND ENGINEERED IN THE UNITED ST DESIGNED AND ENGINEERED IN THE UNITED ST ES BY SAMSON TECHNOLOGIES
www.samsontech.com
POWER
ON
OFF
ACTIVE MONITOR
SPECS:
•20Hz - 20kHz
•BIAMPED 75 WATT
WA WA WOOFER COPOLYMEP C POL POL ONE •25 WATT WA WA TITANIUM FERRO TIT TIT FLUID TWEETER
•TIME ALIGNED WAVEGUIDE WA WA •MAGNETICALLY SHIELDED NETICALL NETICALL WARNING:
RESOLV MONIT LV LV ORS CAN ACHIEVE EXTREMELY HIGH SOUND PRESSURE EXTREMEL EXTREMEL
LEVELS. USE CA LEVELS. LEVELS. UTION OR HEARING DAMAGE MAY RESU GE MA GE MA LT
MID PRESENCE
0dB
-3dB
+3dB
+6dB
VOLUME 0 10
BALANCED
S/N
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN
115-230 vac — 50Hz/60Hz 175W POWER RATING
500 1K 2K 5K
+3 0 -3
-6
+6
R ES P O N SE ( d B )
FREQUENCY (Hz) MID PRESENCE
10 -27
-21
-15 -9
0 5
100 1K 10K 30K FREQUENCY (Hz) CROSSOVER
dBr
10 -50
-30 -15
0 30
50
100 1K 10K 30K
dBr
FREQUENCY RESPONSE FREQUENCY (Hz)
10000.0 10000.0 1000.0 1000.0 100. 100.0
0.00 0.79 1.63 2.43 mSec
SPECTRAL DECAY SPECTRAL DECA SPECTRAL DECA
AUDIO
INPUTS
LINE
MADE IN CHINA DESIGNED AND ENGINEERED IN THE UNITED STAT DESIGNED AND ENGINEERED IN THE UNITED ST DESIGNED AND ENGINEERED IN THE UNITED ST ES BY SAMSON TECHNOLOGIES
www.samsontech.com
POWER
ON
OFF
ACTIVE MONITOR
SPECS:
•20Hz - 20kHz
•BIAMPED 75 WATT
WA WA WOOFER COPOLYMEP CONE
•25 WATT WA WA TITANIUM FERRO TIT TIT FLUID TWEETER
•TIME ALIGNED WAVEGUIDE WA WA •MAGNETICALLY SHIELDED GNETICALL GNETICALL WARNING:
RESOLV MONIT LV LV ORS CAN ACHIEVE EXTREMELY HIGH SOUND PRESSURE EXTREMEL EXTREMEL
LEVELS. USE CA LEVELS. LEVELS. UTION OR HEARING DAMAGE MAY RESU E MA E MA LT
MID PRESENCE
0dB
-3dB
+3dB
+6dB
VOLUME 0 10
BALANCED
S/N
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN
115-230 vac — 50Hz/60Hz 175W POWER RATING
500 1K 2K 5K
+3 0 -3
-6
+6
R ES P O N SE ( d B )
FREQUENCY (Hz) MID PRESENCE
10 -27
-21
-15 -9
0 5
100 1K 10K 30K FREQUENCY (Hz) CROSSOVER
dBr
10 -50
-30 -15
0 30
50
100 1K 10K 30K
dBr
FREQUENCY RESPONSE FREQUENCY (Hz)
FROM MIXER
Connecting to the Resolv120a Subwoofer
Resolv 65a with Mono Sub
Adding a subwoofer and extended low frequency response to your Resolv 65a system is easy using the
RESOLV 65a’s LINE LEVEL inputs. Below is a typical system set-up using the RESOLV 120a with a mixer and a
pair of Resolv 65a’s satellite speakers. The RESOLV 65a’s inputs utilize industry standard RCA connectors. For
a detailed wiring diagram, see the section “RESOLV 65a Connections” on page 12. Follow the steps in the dia-
gram below to set up your system.
• Lower your mixer’s master outputs to all the way off.
•
Connect the mixer’s left output to the RESOLV 120’s LEFT LINE INPUT and the mixer’s right output to
the RESOLV 120’s RIGHT LINE INPUT. Now connect the RESOLV 120’s LEFT LINE OUTPUT to the input of
the left RESOLV 65a, and the RESOLV 120’s RIGHT LINE OUTPUT to the input of the right RESOLV 65a.
• Run an audio signal (like some music from a CD) through your mixer and raise the level to a com-
fortable listening level.
• Now adjust the SWEEP control to the desired frequency. Consult your studio monitors owner’s man-
ual for a recommended crossover point. You can also use your ears by adjusting the SWEEP control to
the frequency that sounds good to you. A good place to start is about 70 Hz.