Sony TAV-L1 - Manual (Page 41)

Usi
ng
the
Mo
nit
o
r Men
u
41 US
Screen menu
You can select the options listed below on the Screen
menu. To select options, see “Navigating through
menus” (page 38).
Selects a Wide Mode to use for 4:3 sources.
1
Press (OK) to select [Wide Mode].
2
Press M/m to select one of the following,
then press (OK).
• [Wide Zoom]: Selects to enlarge to fill screen
with minimum distortion.
• [Normal]: Selects to display 4:3 picture in
original size when the original source is 4:3
(Standard definition source).
• [Full]: Selects to enlarge the original picture
horizontally to fill the screen when the original
source is 4:3 (Standard definition source). When
the original source is 16:9 (High definition
source), select this mode to display 16:9 picture
in original size.
• [Zoom]: Selects to enlarge the original picture
without distorting the aspect ratio.
Tips
• To change from one Wide Mode option to another,
press WIDE.
• For Wide Zoom and Zoom modes, you can adjust the
vertical position of the picture. For details, see
page 41.
• Normal, Full1 and Full2 are available for Wide Mode
when VIDEO 6 is selected.
Selects the default Screen mode to use for 4:3 sources.
1
Press (OK) to select [4:3 Default].
2
Press M/m to select one of the following,
then press (OK).
• [Wide Zoom]: Selects to enlarge the 4:3 picture
to fill the 16:9 screen, keeping the original image
as much as possible.
• [Normal]: Selects to return the 4:3 picture to its
original size.
• [Full]: Selects to enlarge the 4:3 picture
horizontally only, to fill the 16:9 screen.
• [Zoom]: Selects to enlarge the 4:3 picture
horizontally and vertically to an equal aspect
ratio that fills the 16:9 screen. Useful for
watching Letterbox movies.
• [Off]: Selects to continue using the current Wide
Mode setting when the channel or input is
changed.
Tips
• 4:3 Default functions only when the monitor receives
480i or 480p signals.
• If 4:3 Default option is set to anything but [Off], the
Wide Mode setting changes only for the current
channel. When you change channels (or inputs), Wide
Mode is automatically replaced with the 4:3 Default
setting for 4:3 sources. To retain the current Wide
Mode setting as channels and inputs are changed, set
4:3 Default to [Off].
Note
This setting is not available for VIDEO 6.
Allows you to adjust the viewable picture area size.
1
Press (OK) to select [Overscan].
2
Press M/m to select one of the following,
then press (OK).
• [Normal]: Displays a standard size picture.
• [+1]/[+2]: Allows you to adjust the viewable
picture area size. This is useful for viewing
ticker tape or banners at the top or bottom of the
screen.
Note
This setting is not available for VIDEO 6.
Allows you to move the position of the picture up and
down in the window. Available only in Wide Zoom
and Zoom modes.
1
Press (OK) to select [V Center].
2
Press M/m to choose a correction
between -10 and +10, then press
(OK).
Tip
The setting of V Center can be between –50 and +50 for
VIDEO 6.
Wide Mode
4:3 Default
Back: Select: Set:
Screen
Wide Mode: Wide Zoom
4:3 Default: Wide Zoom
Overscan: Normal
V Center:
0
H Center: 0
Phase:
Pitch:
Reset:
Exit:
Video 1
MENU
Overscan
V Center (Vertical Center)
Continued