Superior BC36MH User Manual
Page 7
7
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Blower Kit is installed as
a standard component
on model BCD36MH
(optional kit for model
BC36MH)
AccEssoRY coMPoNENts
Blower Kit
Forced Air Blower Kit
cat. No.
Model No.
description
36L32
BFK36
Forced Air Blower Kit
oN/oFF Wall
switch Kit
This ON/OFF wall switch kit
can be used in place of the
unit mounted rocker switch.
This switch provides single
speed ON/OFF operation
of the blower. Install the
ON/OFF wall switch in a
convenient location near
the fireplace.
White Wall switch Kit
cat. No.
Model No.
description
85L87
FWsK
oN/oFF Wall switch Kit
tRouBLEsHootiNG
Note: "Smoke Free" operation is not warranted
nor are we responsible for inadequate system
draft, general construction conditions, inad-
equate chimney heights, adverse wind condi-
tions and/or unusual environmental factors or
conditions beyond our control.
If you do experience a problem, here are several
things to check:
. Remember – always check to ensure your
flue damper is in the open position before
lighting a fire!
2. When lighting your fire, a little smoke may
escape into the room – more likely if the
chimney is cold. To correct this, hold a
lighted newspaper up inside the firebox near
the open flue damper. This will turn around
any downdraft and clear the flue of cold air.
As your log fire burns below, the updraft will
improve as the chimney heats up.
3. Is your fire too far forward? Move it toward
the back with your poker. Keep the fire well
within the confines of your fuel grate.
4. Keep your fire up on the grate and the refrac-
tory below free of excessive ashes. The fire
needs plenty of air movement around the
logs.
5. If smoking occurs an hour or two after
lighting the fire, perhaps your well-insulated
house is too airtight and there is scarcely any
way for replacement air to enter and feed the
fire. Check to see if your outside combustion
air kit (if installed) is open. Check outside
to ensure no obstructions are in front of
exterior air entry. Open a window slightly,
open doors to one or two rooms and see if
this stops the smoking.
6. Is a vent fan, exhaust hood or central heat-
ing/cooling system stealing combustion air
from your fireplace? If their volume is high
enough, this can cause negative pressure and
an unwanted downdraft – and smoking.
7. Is your wood fuel too wet or unseasoned?
Or does it contain some chemical substance
that causes sputtering, smoking and toxic
fumes?
8. Figure 5 illustrates the correct height of
your chimney top. It is unlikely that your
installation does not adhere to the instal-
lation instructions. However, if not correct,
you could experience an unusual downdraft.
Usually, the best solution is to increase the
chimney height. This may also be necessary
if nearby trees, adjoining roof lines or a hill
is causing a downdraft condition.
9. Remember, your fireplace is not intended
to heat your entire home.
Figure 5
Less Than 10'
3'
Min
2' Min.
10'
3'
Min
Your Fireplace's Model Number ________________________________________
Your Fireplace's Serial Number ________________________________________
The Date On Which Your Fireplace Was Installed ___________________________
Your Dealer's Name ________________________________________________
WARRANtY
• This fireplace is covered by a limited warranty detailed separately from this document.
• Retain this manual. File it with your other documents for future reference.
PRoduct REFERENcE iNFoRMAtioN
If you encounter any problems or have any questions concerning the installation or application of
this system, please contact your distributor or installer. For the number of your nearest Superior
dealer, please call 1-800-953-6669.
LHP
0 West taft Avenue
orange, cA 92865
REPLAcEMENt PARts
A complete parts list is found at the end of this manual. Use only parts supplied from the manu-
facturer.
Normally, all parts should be ordered through your Superior distributor or dealer. Parts will be
shipped at prevailing prices at time of order.
When ordering repair parts, always give the following information:
. The model number of the appliance.
4. The description of the part.
2. The serial number of the appliance.
5. The quantity required.
3. The part number.
6. The installation date of the appliance.