Sharp 28LF-92H - Manual (Page 15)

- 14 -
INSTALL. (Installation) Menu
You can store a channel manually, or modify the current set-
tings of a channel (for example, fine-tuning a channel).
You can also change the colour system.
• Press “M” button to display the main menu.
• Press “ ” or “ ” button to select “INSTALL.” item. Then
“ ” or “ ” button to display the “INSTALL.” menu.
6281'
3,&785(
)($785(
,167$//
352*5$0
Note:
• If you want to modify the current settings of a channel, se-
lect the channel of which you want to modify the setting.
Then display the main menu on screen.
• In AV mode, you can change only the “COLOUR SYSTEM”
item.
1. PROGRAMME is the first selected item as you enter the
INSTALL. menu. Press the “ ” or “ ” button to select the
programme number where you want the tuned channel to
be stored. (You may also type the programme number us-
ing the digit buttons)
Note:
• Do not use the PROGRAMME item when you want to
modify the current programme number setting as this may
cause other programmes to be changed that are in the ex-
isting programme number.
2. Press “ ” or “ ” button to select Tuning Mode. By press-
ing “ ” or “ ” button , you can select the mode in which
you want the search to be made, "Channel Search"
mode or "Frequency Search" mode.
• When you select "Channel Search" ("Channel" will be
displayed in the menu.), the display of the
INSTALL.(Installation) Menu will be as below :
QSPBS6HH@
UVIDIBÃHP9@
76I9
8C6II@G
8PGPVSÃT`TU@H
ADI@ÃUVIDIB
T@6S8C
Q#
8C6II@G
T
%
Q6G
3. Press “ ” or “ ” button to select BAND. Using “ ” or “ ”
button to select the band in which you want to search a
channel.
4. Press “ ” or “ ” button to select SEARCH. Press “ ” or
“ ” button to start searching. (Press “ ” button to search
forward. Press “ ” to search backwards.)
• If the found channel is not the desired one, press “ ” or
“ ” button to start searching again.
• To stop searching before a channel is found, press the
reverse direction button. For example, when the TV is
searching forward with “ ” button, press “ ” button to
stop searching.
• If you know the channel number which you want to find,
you can find the channel directly. Follow the step 5 to
select the correct standard, then press “ ” or “ ” to
select CHANNEL again, and press“ ” or “ ” button to
select the channel number, or enter the number with the
digit buttons.
5. If the picture is not clear or no colour appears, change the
colour system to display the picture normally. Press “ ”
or “ ” button to select COLOUR SYSTEM, then press “ ”
or “ ” button to choose the correct one.
• In TV mode: PAL / SECAM
• In AV mode: AUTO / PAL / SECAM / NTSC 3.58 /
NTSC 4.43
6. If the channel reception is poor, fine-tune the channel.
Press “ ” or “ ” to select FINE TUNING, then press “ ”
or “ ” button to fine-tune the channel.
7. After the all settings are completed, store the new
channel’s setting to the programme number which you se-
lected. Press “ ” or “ ” to select STORE, then press
“ ” or “ ” button to store it.
UVIDIBÃHP9@
76I9
8C6II@G
8PGPVSÃT`TU@H
ADI@ÃUVIDIB
T@6S8C
TUPS@
8C6II@G
T
%
Q6G
8. When you select "Frequency Search" , the display of the
Tuning menu will be as below :
QSPBS6HH@
UVIDIBÃHP9@
8PGPVSÃT`TU@H
AS@RV@I8`
T@6S8C
TUPS@
Q#
AS@RV@I8`
Q6G
#!$
• As "Frequency Search" is selected, TV will search ac-
cording to the channel frequencies.
• With the“ ” or “ ” button, select Search. Search can be
made either forward, pressing “ ” button or backwards,
pressing “ ” button.
• The search will be done with steps of 0.25MHz. in each
step.
• If the tuned station is not the desired one, you can continue
searching pressing “ ” or “ ” button again.
• When the desired station is tuned, select STORE using
“ ” or “ ” button and store it to the programme number
you selected pressing “ ” or “ ” button or press “OK” but-
ton.
• Now as you had selected the Frequency Search, the tuning
mode of the program is stored as Frequency Search Mode.
Direct Frequency Access
• If you know the broadcast band and the channel frequency
of the station you want to tune, you do not need to make
search; select Frequency, using “ ” or “ ” button in the
Frequency Mode Tuning Menu. You can type the first 3 dig-
its of the frequency using the digit buttons, and then you
can select the decimal part of the frequency by using “ ” or
“ ” buttons with 250kHz steps. For example if you want to
tune the station at frequency 224.25 MHz; first you can di-
rectly type 224. The bar at bottom of the menu will show
224.00 . Then by increasing or decreasing with 0.25 MHz
steps using “ ” or “ ” buttons, you can select the
224.25MHz .When you type and select the frequency, the
corresponding station will be displayed.
ENG-2862W-3262W-1548UK-2SCART-FAV-SVHS-AK45-SHARP-TV-1.p65 21.01.2004, 08:28 14