Skylink 318TRS - Manual (Page 2)

BATTERY
If, within one year from date of purchase, this product should become defective
(except battery), due to faulty workmanship or materials, it will be repaired or
replaced, without charge. Proof of purchase and a Return Authorization are required.
10. WARRANTY
On the garage door receiver
and wireless switch receiver,
remove the screw that holds
the connector covers, and
remove the covers.
You will see 10 connectors. For connectors “1” to “9”, the settings
must match with those of the transmitter.
Connector 10 on the receiver should be set to “+” if it is controlled by
the transmitter’s left button , connector 10 on the receiver should be
removed if it is controlled by the transmitter’s right button. Example, if
the left button is used to control the garage door receiver, connector
10 on the garage door receiver should be set to ”+”. If the right button
is used to control the wireless switch receiver, connector 10 on the
wireless switch receiver should be removed.
Connector 10 “Removed”
Connector 10 set to “+”
TRANSMITTER
You can add as many additional transmitters as you
want to control the same receiver. Simply set the same
operation code on all transmitte rs with the same code
setting on the receiver. Skylink
®
offers Keychain
Transmitter Model 318TN to work with your receiver. For
more information, please visit our website at
www.skylinkhome.com or contact us.
7. ADDITIONAL TRANSMITTER
RISK OF ELECTRICAL SHOCK. FOR INDOOR USE ONLY.
CAUTION : NOT FOR USE WITH DIMMER.
CAUTION : DISCONNECT POWER BEFORE CODE CHANGING.
REPLACE COVER AFTER CODE CHANGING.
8. CAUTION
9. FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference
received, including interference that may cause undesired operation.
WARNING:
Changes or modifications to this unit not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause ha rmful interfere nce to radio or television rec eption, which can be determined by turning the equipment
off and on, the user is encourage d to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
5
6
7
WIRELESS SWITCH RECEIVER
SW-318R
GARAGE DOOR RECEIVER
318R
Connectors
1 to 9 are
the same.
8 Put the cover and screw back onto the receivers. Install the garage
door receiver and wireless switch receicer based on previous
illustrations on sections 2 and 4.
Put the battery cover back onto the transmitter.
Press the left button on the transmitter to operate the garage door receiver
or press the right button to turn on/off the light fixture/small appliance.
9
12 volt alkaline battery (size 23A)
(included).
It is time to change the battery
when the red LED on the trans-
mitter does not turn on when
either button is pressed.
6. BATTERY
11. CUSTOMER SERVICE
CUSTOMER SERVICE
17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3
Email:[email protected]
http://www.skylinkhome.com
P/N. 101A231-002 Rev.2
US Patent. D380895
©2005 SKYLINK GROUP
If you would like to order Skylink’s products or have difficulty getting them to work,
please :
1. visit our FAQ website at www.skylinkhome.com, or
2. email us at [email protected], or
3. call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST.
Fax +800 286-1320
10
MODEL :318R
Maximum Rating:
Input : 120VAC 60Hz 2W
MODEL :SW-318R
Maximum Rating :
Input : 120VAC 60Hz
Resistive load : 8A (960W)
Incandescent : 300 watts
Motor Load : 1/3 HP
If the connector is placed on the top and middle posts, that column is
set on “ + ” . If the connector is placed on the middle and bottom posts,
that column is set on “ - ”. If the connector is removed completely, (not
placed on any posts), it is set to “ 0 ”. (see
diagram for examples of how to set a
column to the three different positions).
When removing a connector to set a
column to “ 0 ”, save the connector in
case you change the code at a later date.
After setting up the code connectors on the transmitter, you
are ready to set the same code on the receivers.
Remove the receiver from the electrical outlet before
changing the code.
3
4
WARNING
2
5. CHANGE THE OPERATION CODE FOR
BOTH TRANSMITTER AND RECEIVERS
1
BATTERY
‘+’
‘-’
‘ 0 ’
Follow the instructions below if you want to change the operation code.
Pry off the battery
cover of the trans-
mitter with a coin,
as shown.
You will see 9 connectors labeled
from “1” to “9”, as shown. (the
connectors setting may not be the
same as shown.)
You can randomly remove some
connectors, leaving some in place.
A connector can be removed with
the clip, as shown.