Skil 2255 - Manual (Page 12)

12
b) Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or the
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools.
Such preventive safety measures reduce the risk
of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool.
Power to-
ols are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or bin-
ding of moving parts, breakage of parts and any other
condition that may affect the power tools operation. If
damaged, have the power tool repaired before use.
Many
accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintai-
ned cutting tools with sharp cutting edges are less likely
to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc. in ac-
cordance with these instructions and in the manner in-
tended for the particular type of power tool, taking into
account the working conditions and the work to be per-
formed.
Use of the power tool for operations different from
those intended could result in a hazardous situation.
5) Battery tool use and care
a) Ensure the switch is in the off position before insert-
ing battery pack. Inserting the battery pack into power
tools that have the switch on invites accidents.
b) Recharge only with the charger specified by the manu-
facturer. A charger that is suitable for one type of battery
pack may create a risk of fire when used with another
battery pack.
c) Use power tools only with specifically designated bat-
tery packs. Use of any other battery packs may create a
risk of injury and fire.
d) When battery pack is not in use, keep it away from
other metal objects like paper clips, coins, keys, nails,
screws, or other small metal objects that can make a
connection from one terminal to another.
Shorting the
battery terminals together may cause burns or a fire.
e) Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally oc-
curs, flush with water. If liquid contacts eyes, addition-
ally seek medical help.
Liquid ejected from the battery
may cause irritation or burns.
6) Service
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
Safety instructions for cordless drill/drivers
• Read and save this instruction manual.
• Avoid damage that can be caused by screws, nails and
other elements in your workpiece; remove them before you
start working.
• Check voltage indicated on nameplate of tool/charger/battery.
• In case of electrical or mechanical malfunction, immediately
switch off the tool or unplug charger from power source.
• SKIL can assure flawless functioning of the tool only when
original accessories are used.
• Before using accessories always compare the maximum al-
lowed r.p.m. of that specific accessory with the r.p.m. of the
tool.
• This tool should not be used by people under the age of 16
years.
• Be careful not to drill or drive into areas where electrical
wires may be contacted.
• Do not activate switch when changing accessories or carry-
ing the tool.
CHARGING/BATTERIES
• Charge battery only with the charger that is supplied with
the tool.
• Do not touch the contacts in the charger.
• Do not expose tool/charger/battery to rain.
• Never charge battery outdoors.
• Store tool/charger/battery in locations where temperature
will not exceed 40 °C or drop below 0 °C.
• Batteries will explode in fire, so do not burn battery for any
reason.
• When damaged, and under extreme usage and tempera-
ture conditions, batteries may start to leak.
- If liquid comes into contact with the skin, wash quickly
with soap and water, then with lemon juice or vinegar.
- If liquid gets into the eyes, flush eyes with clean waterfor
a minimum of 10 minutes and seek immediately medical
attention.
• When battery is not in tool or charger, it should be kept
away from metal objects such as nails, screws, keys etc. to
prevent short-circuit.
• Do not use charger when damaged; take it to one of the of-
ficially registered SKIL Service Stations for a safety check.
• Do not use charger when cord or plug is damaged; cord or
plug should be replaced immediately at one of the officially
registered SKIL Service Stations.
• Do not disassemble charger or battery.
• Do not attempt to recharge non-rechargeable batteries with
the charger.
WHEN CONNECTING NEW 3-PIN PLUG
• Do not connect the blue (= neutral) or brown (= live) wire in
the cord of the charger to the earth terminal of the plug.
• If for any reason the old plug is cut off the cord of the char-
ger, it must be disposed of safely and not left unattended.
Use
CHARGING BATTERY (fig. A)
• Battery of new tools is not fully charged.
! Remove battery from charger after charging period has
ended thereby lengthening the service life of the battery.
IMPORTANT:
• After 3 hours the charging operation will be completed, and
the battery may be used, even though the red light may
still be on (the red light may require more than 3 hours to
turn off).
• While charging, the charger and the battery may become
warm to touch; this is normal and does not indicate a prob-
lem.
• Ensure that the outside surface of the battery is clean and
dry before inserting into charger.
• Do not charge at temperatures below 0 °C and over 40 °C;
this will seriously damage the battery as well as the charger.
• Do not remove battery from tool while it is running
• When you charge the battery for the first time, it only ac-
cepts 80% of its maximum capacity; after several charges
and discharges, however, the batteries should be at full ca-
pacity and deliver maximum performance.
skil_2255/2355/2455 6/22/04, 18:01 12