Kambrook KCE45 - Manual (Page 3)

Do not insert or allow foreign objects to
pass through the inlet or outlet openings.
This may cause an electric shock, fire or
damage the heater.
To prevent a possible fire or heat damage,
allow ample space around the heater (at
1.7m at front and 0.5m at the rear, top
and sides) and do not totally or partially
block the air inlet or outlets in any manner.
Check the openings from time to time for
accumulated dust. Ensure long shag carpet
does not obstruct airflow under the unit.
Do not touch hot metal surfaces.
Switch off at the control switch and power
outlet, then unplug and allow heater to
cool down before cleaning or storing.
Use this heater only as described in this
instruction manual. Any other use not
recommended by the manufacture may
cause fire electric shock or injury and
voids all warranties.
Regularly inspect the supply cord, plug,
control settings, air inlets and outlets and
main housing for any damage. If found
damaged in any way, immediately cease use
of the heater and return to Kambrook or
an authorised service agent for inspection
or repair.
The installation of a residual current
device (safety switch) is recommended to
provide additional safety protection when
using electrical appliances. It is advisable
that a safety switch with a rated residual
operating current not exceeding 30mA be
installed in the electrical circuit. See your
electrician for professional advice.
HOW TO OPERATE
Remove your heater from its carton and
associated protective wrapping, and
unwind the cord to its full length and
remove and protective cardboard or foam
that may have been used to minimise
transportation damage.
Place the heater on a firm, level surface
in a stable upright position.
Visually inspect the air inlet and outlets
to ensure no foreign material is blocking
these areas.
Make certain the main power button located
on the front of the base is not depressed and
in the OFF position.
The heater must always be operated with the
rear air filter in position.
Plug the power cord in a 230-240 volt power
outlet.To avoid an electrical circuit overload,
it is recommended that no other appliances
are plugged into the same circuit with your
heater when you switch the unit on.
Control the heater with the selector
settings as follows:
Turn the heater on by pressing the main
control switch on the front of the base.
The red neon light will illuminate when
power is being supplied to the heater.
Press Power on the main control panel
or remote control. The heater will default
to the AUTO setting.
To adjust the temperature setting either
increase or decrease the setting by
pressing the Up and Down buttons.
The Setting button will allow the unit to
be set to either AUTO, COOL, LO or
HIGH settings.
During AUTO operation the power setting
is determined by the ambient temperature
and that set by the consumer using the Up
and Down buttons on the heater.
During COOL operation the heater will
only distribute cool air and the heating
elements are not operational
During LO operation the heater will
always operate at 1000 Watts
During HIGH operation the heater
will always operate at 2000 Watts
Note: During COOL, LO and HIGH settings the
temperature display will show the ambient
temperature and cannot be adjusted using the
UP or DOWN buttons.
Press the Oscillating button to active the
oscillation function. The unit will Oscillate
40º to each side. To adjust the Oscillation
direction turn the unit OFF and manually
position the heater to the correct position
by gently twisting the main housing of the
heater.
The heater has a count down timer
ranging from 8 hours to 1 hour. Press the
Timer button once to increase the hour
setting by one hour increments. After 8
depressions the timer will be off and no
figure will appear on the LCD display.
This heater is fitted with an Ioniser.
By turning on the Ioniser, the heater will
generate and emit positive Ions into the
room, which will react with negative
particles in the air. The result is that these
air particles will then fall to the ground
resulting in cleaner air within the room.
Therefore you may find a build up of
particles at the base of the heater after
prolonged usage in the Ionisation setting.
All the control features can be operated
using the supplied remote control when
the main power switch located on the
base of the heater is turned on and the
remote is pointed directly to the front
of the heater.
When the heater is first switched OFF, at
the conrol pad, the fan setting will remain
on until the Ceramic elements cool down.
This is a normal safety operation.
Note: there is a tip over switch fitted to this heater.
When the heater tips over it will automatically
turn off.
Thermoguard Overheating
Safety Device
Your heater is fitted with a safety device
that switches off the heater in the event
of overheating. Should this heater stop
working, turn off the heater and inspect
for blockages or air inlet or outlets.Wait
at least five minutes for the protection
system to reset before attempting to
restart the heater.
If the heater fails to operate or the safety
device switches off again, return the heater
to your nearest service centre for
examination or repair.
4 5