Kettler 07122-890 - Manual (Page 2)

2
Before assembling or using the table-tennis table, please read the following instructions carefully. They contain impor-
tant information for use and maintenance of the equipment as well as for your personal safety. Keep these instructions
in a safe place for maintenance purposes or for ordering spare parts.
All KETTLER products are designed in accordance with the latest safety regulations and undergo a constant process of quality control
during manufacturing. The knowledge gained in this process is used to constantly improve and develop our products. In order to offer
our customers the very best in product quality, we reserve the right to make technical changes at any time. In spite of this, should you
have any cause for complaint, please contact KETTLER.
Note on Safety
■ The table-tennis table should be used only for its intended purpose,
i.e. for playing with suitable table-tennis racquets and balls.
■ All other uses are prohibited and may be dangerous. The man-
ufacturer cannot be held liable for damage or injury caused by
improper use of the table.
■ Damaged or worn components may endanger your safety or short-
en the lifespan of the table-tennis table. Replace worn or damaged
components immediately and remove the table from use until this
has been done. Use only spare parts manufactured by KETTLER.
■ The table-tennis table complies with all safety regulations. In-
correct repairs, alterations to the design (removal of original
parts, addition of other components etc.) may endanger the
safety of the user.
■ Instruct other persons (in particular children) using the table in
its correct use, and draw their attention to any potential source
of danger, especially when setting up or dismantling the table.
■ When setting up or dismantling the table, stay clear of its folding radius.
■ When folded up, the table-tennis table presents a large surface
to the wind. For this reason, ensure that it is stored in a shel-
tered position.
■ The table-tennis table may be pushed only into the transport po-
sition because there is otherwise a danger of injury.
■ The unit complies with the standard EN 14468–1:2004.
■ Depending on frequency of use, check all screws, bolts etc. reg-
ularly to ensure that they are in good condition.
■ In case of enquiry, please contact your KETTLER dealer.
Handling the equipment
■ Do not use the table-tennis table until it has been fully and cor-
rectly assembled and checked.
■ Ensure that indoor table-tennis tables are not exposed to damp-
ness or rain. Keep them well away from direct sources of heat.
Should the surface become warped, lay the table on a level sur-
face for a few days.
■ Set the table up on a level surface.
■ Do not cover it with plastic foil, under which condensation may
form. To protect your outdoor table keep it closed and covered by
the KETTLER table tennis cover (item # 7032-400) when not in use.
■ For practicing without a partner, the table halves can be folded
up singly.
■ For more information on the sport of table-tennis, you are re-
ferred to the specialist literature on the subject.
■ Do not use corrosive or abrasive materials to clean the equip-
ment. Ensure that such materials are not allowed to pollute the en-
vironment. In most cases, a slightly dampened cloth is sufficient.
■ Waste Disposal: KETTLER products are recyclable. At the end of
its useful life please dispose of this article correctly and safely
(local refuse sites).
Instructions for Assembly
■ The equipment must be assembled with due care by two adult
persons.
■ Ensure that you have received all the parts required (see check
list) and that they are undamaged. Should you have any cause
for complaint, please contact your KETTLER dealer.
■ Before assembling the equipment, study the drawings carefully
and carry out the operations in the order shown by the dia-
grams. The correct sequence is given in capital letters.
■ Please note that there is always a danger of injury when work-
ing with tools or doing manual work. Therefore please be care-
ful when assembling this machine.
■ Ensure that your working area is free of possible sources of dan-
ger, for example don’t leave any tools lying around. Always dis-
pose packaging material in such a way that it may not cause
any danger. There is always a risk of suffocation if children
play with plastic bags!
■ The fastening material required for each assembly step is shown
in the diagram inset. Use the fastening material exactly as in-
structed.
■ Bolt all the parts together loosely at first, and check that they
have been assembled correctly. Tighten the locknuts by hand
until resistance is felt, then use wrench to finally tighten nuts
completely against resistance (locking device). Then check that
all screw connections have been tightened firmly. Attention:
once locknuts have been unscrewed they no longer function cor-
rectly (the locking device is destroyed), and must be replaced.
■ For technical reasons, we reserve the right to carry out prelimi-
nary assembly work (e.g. addition of tubing plugs).
■ Please keep original packaging of this article, so that it may be
used for transport at a later date, if necessary.
List of spare parts
When ordering spare parts, always state the full article number, spare-
part number, the quantity required and the S/N of the product (see spa-
re parts drawing).
Example order: Art. no. 07122-890 / spare-part no. 10100016 / 2
pieces / S/N......
Important: spare part prices do not include fastening material; if fasten- ing material (bolts, nuts, washers etc.) is required, this should be clearly
stated on the order by adding the words „with fastening material“.
For parts and service ONLY call 866.804.0440 or send email to
[email protected]
KETTLER International Inc. · 1355, London Bridge Road · Virginia
Beach, VA 23453 USA
Important notes