Messages transmitted and received by the microkorg, Control 2 values when osc 1 wave = dwgs, Osc 2 semitone values – KORG Synthesizer/Vocoder MICRO User Manual
Page 63
57
Control 2 values when OSC 1 Wave = DWGS
When the synth parameter OSC 1 "WAVE" is set to DWGS, the "CONTROL 2" (knob 3 )
will select the DWGS waveform. The value of the control change transmitted/received
by operating the "CONTROL 2" (knob 3 ) corresponds to the parameter value as
follows.
0, 1
1
2, 3
2
4, 5
3
6, 7
4
8, 9
5
10, 11
6
12, 13
7
14, 15
8
16, 17
9
18, 19
10
20, 21
11
22, 23
12
24, 25
13
26, 27
14
28, 29
15
30, 31
16
32, 33
17
34, 35
18
36, 37
19
38, 39
20
40, 41
21
42, 43
22
44, 45
23
46, 47
24
48, 49
25
50, 51
26
52, 53
27
54, 55
28
56, 57
29
58, 59
30
60, 61
31
62, 63
32
Value
(transmitted, received)
Value
(transmitted, received)
DWGS Wave
DWGS Wave
64, 65
33
66, 67
34
68, 69
35
70, 71
36
72, 73
37
74, 75
38
76, 77
39
78, 79
40
80, 81
41
82, 83
42
84, 85
43
86, 87
44
88, 89
45
90, 91
46
92, 93
47
94, 95
48
96, 97
49
98, 99
50
100, 101
51
102, 103
52
104, 105
53
106, 107
54
108, 109
55
110, 111
56
112, 113
57
114, 115
58
116, 117
59
118, 119
60
120, 121
61
122, 123
62
124, 125
63
126, 127
64
Messages transmitted and received by the microKORG
OSC 2 Semitone values
The value of the control change transmitted/received by operating OSC 2
"SEMITONE" (knob 3 ) of a synth program corresponds to the parameter value as
follows.
0...2
–24
3...5
–23
6, 7
–22
8...10
–21
11...13
–20
14, 15
–19
16...18
–18
19, 20
–17
21...23
–16
24...26
–15
27, 28
–14
29...31
–13
32, 33
–12
34...36
–11
37...39
–10
40, 41
–9
42...44
–8
45...47
–7
48, 49
–6
50...52
–5
53, 54
–4
55...57
–3
58...60
–2
61, 62
–1
63...65
0
Value (transmitted, received)
OSC 2 Semitone
Value (transmitted, received)
OSC 2 Semitone
66, 67
+1
68...70
+2
71...73
+3
74, 75
+4
76...78
+5
79, 80
+6
81...83
+7
84...86
+8
87, 88
+9
89...91
+10
92...94
+11
95, 96
+12
97...99
+13
100, 101
+14
102...104
+15
105...107
+16
108, 109
+17
110...112
+18
113, 114
+19
115...117
+20
118...120
+21
121, 122
+22
123...125
+23
126, 127
+24
"SYNC NOTE" value when LFO 1/2 or DELAY "TEMPO SYNC" = ON
If "TEMPO SYNC" is ON, the parameter that is set by the LFO 1/2 "FREQUENCY"
(knob 4 ) or the DELAY "DELAY TIME" (knob 3 ) will change to "SYNC NOTE." In this
case, the value of the control change message transmitted by knob operations (or
received) will correspond to the parameter value as shown below.
0...8
1/1
1/32
9...17
3/4
1/24
18...25
2/3
1/16
26...34
1/2
1/12
35...42
3/8
3/32
43...51
1/3
1/8
52...59
1/4
1/6
60...68
3/16
3/16
69...76
1/6
1/4
77...85
1/8
1/3
86...93
3/32
3/8
94...102
1/12
1/2
103...110
1/16
2/3
111...119
1/24
3/4
120...127
1/32
1/1
LFO Sync Note DELAY Sync Note
Value (transmitted, received)