Kambrook Jaguar Power Twister KBV30 - Manual (Page 3)

5
can be stored on the telescopic wand tool
storage stand for easy access and storage.
Turn the vacuum cleaner OFF when
changing any attachments.
Park Tool Feature
The park tool feature can be used to park
the wand in the upright (storage) position
The park tool attachment hook, for upright
storage is located on the lower wand.
With the vacuum switched off and
unplugged from the power point, insert
the park tool hook into the park tool
receptacle on the vacuum body
Note:The floor tool should be attached and in
contact with the floor to give stability, if correctly
assembled.
Emptying the Dust Canister
The dust canister should be emptied
when the dust inside the canister reaches
the max marking (indicated on the side of
the canister).
Always switch the appliance off, then
switch off at the power outlet and unplug
the appliance prior to emptying the dust
canister or changing filters.
To remove the dust
canister, press the ‘dust
canister compartment
release button’ located
on the side of the unit.
The canister will then
slide out.
NOTE:The canister compartment lid may not close
if the canister is not correctly fitted.
IMPORTANT: DO NOT USE THE
UNIT WITHOUT THE DUST
CANISTER IN PLACE
Replacing / Cleaning filters
HEPA and Micro Dust Filter
There are 2 dust filters located inside the
dust canister.The outer filter is the Micro
Dust filter and the inner filter is the HEPA
filter.
To remove these filters for cleaning, follow
the instructions listed under ‘Emptying the
dust canister’ on page 5.
Once the dust canister lid has been
removed, hold the top of the lid with one
hand and grasp the bottom of the filter
with the other hand to separate the filters
from the dust canister
lid.You may need to
rotate the bottom of
the filter slightly
clockwise to release.
The HEPA filter and Micro dust filter can
be washed in lukewarm water. Allow to
dry completely before placing the filters
back into the dust canister.
To reposition the HEPA filter and Micro-
filter follow these steps:
1. Hold the base of the HEPA filter
2. Slide the Micro-dust filter over the
HEPA filter
3. Still holding the base of the filter in one
hand, take the dust canister lid in the
other hand and push the filter onto the lid
so that the round opening in the filter fits
over the round opening in the dust
canister lid.
4
Using Your Kambrook Jaguar
‘Power Twister’ Bagless
Vacuum Cleaner
Remove all packaging from the unit, hose
and other accessories; ensure that you
have removed all of the accessories before
discarding the packaging.
Ensure that the dust canister and filters
are correctly fitted.
Locate the crush proof hose and push the
connection point into the hose inlet
connection on the top of the unit, until a
“click” sound is heard.
To extend the telescopic wand, push the
extension lever in the direction of the
arrow (printed on the lever) and pull out
the narrower tube to the desired height.
Connect the wide end of the telescopic
tube on to the hose end, and push
together firmly.
Fit the floor head to the narrow end of
the wand and push together firmly
Fully extend the power cord by pulling
the power plug (situated at the rear of the
unit) out from the unit, until the yellow
tape on the cord is shown.
ENSURE THAT YOU DO NOT
OVER EXTEND THE POWER
CORD – DO NOT EXTEND PAST
THE RED WARNING TAPE ON
THE CORD
Plug into a 230/240v power point and
switch the power on.
To commence vacuuming push down on
the on/off foot pedal, at the top, rear of
the unit.
For full suction power ensure that the
fingertip suction control cover (on the
top of the hose) is closed.The suction
power can be reduced by opening the
suction control cover.
When vacuuming is complete, turn the
vacuum cleaner ‘OFF’ by pushing down on
the ‘ON/OFF’ foot pedal.Turn the power
off at the outlet and then remove the
power cord from the power outlet (when
removing plug from the power outlet
grasp the plug not the cord).
To retract the cord push down on the
‘cord rewind’ foot pedal.
IMPORTANT: HOLD THE PLUG
END WHEN RETRACTING THE
CORD TO PREVENT IT FROM
STRIKING YOU OR THE VACUUM.
ALWAYS ENSURE THAT THE
DUST CANISTER IS CORRECTLY
FITTED. NEVER OPERATE
WITHOUT THE DUST CANISTER
IN PLACE.
Crevice and brush tool accessories
The crevice tool is ideal for vacuuming
hard to reach places such as the edges
along skirting boards, crevices, corners
and in between cushions.
The upholstery tool can be used to
vacuum delicate surfaces and areas such
as shelves, venetian blinds , furniture and
lamp shades.
When using the crevice and upholstery
tools, slide the Fingertip Suction Control
cover (located on the wand handle) to the
open position to reduce suction.
Both the Crevice and Uupholstery tools