Kawasaki 840378 User Manual
Page 10
18
L
LA
AS
SE
ER
R S
SA
AF
FE
ET
TY
Y
N
NE
EV
VE
ER
R L
LO
OO
OK
K IIN
NT
TO
O T
TH
HE
E L
LA
AS
SE
ER
R B
BE
EA
AM
M.. Any contact with the eyes by the beam
could cause injury. Do not use the laser when cutting reflective materials.
D
DO
O N
NO
OT
T A
AIIM
M T
TH
HE
E L
LA
AS
SE
ER
R B
BE
EA
AM
M A
AT
T A
AN
NY
YO
ON
NE
E O
OR
R A
AT
T R
RE
EF
FL
LE
EC
CT
TIIV
VE
E S
SU
UR
RF
FA
AC
CE
ES
S..
C
CL
LA
AS
SS
S 2
2M
M L
LA
AS
SE
ER
R P
PR
RO
OD
DU
UC
CT
T.. Any contact with the eyes by the beam could
cause injury. Ensure the laser beam is turned on only when the tool is on a non-
reflective workpiece and as such it is aimed only at the work surface. Metals and
other materials like steel which can be highly reflective should only be cut with-
out the use of the laser.
S
ST
TO
OR
RE
E O
OU
UT
T O
OF
F R
RE
EA
AC
CH
H O
OF
F C
CH
HIIL
LD
DR
RE
EN
N.. Equipment should be in a high location
or locked up to keep out of reach of children. It is not a toy.
D
DO
O N
NO
OT
T T
TA
AM
MP
PE
ER
R W
WIIT
TH
H T
TH
HE
E L
LA
AS
SE
ER
R O
OU
UT
TP
PU
UT
T.. Changing the performance of the
laser to increase its output is prohibited. Any claim for damages or injuries
resulting from not following these instructions will be refused.
O
OP
PE
ER
RA
AT
TIIO
ON
N A
AC
CC
CE
ES
SS
SIIB
BL
LE
E F
FIIE
EL
LD
DS
S::
Wavelength
636-660nm
Laser Power for Classification
<1mW CW
N
NE
EV
VE
ER
R O
OP
PE
ER
RA
AT
TE
E L
LA
AS
SE
ER
R IIF
F T
TH
HE
E U
UN
NIIT
T IIS
S D
DE
EF
FE
EC
CT
TIIV
VE
E O
OR
R T
TH
HE
E C
CO
OV
VE
ER
R O
OR
R S
SE
EA
AL
L
IIS
S D
DA
AM
MA
AG
GE
ED
D..
D
DO
O N
NO
OT
T S
SE
ER
RV
VIIC
CE
E L
LA
AS
SE
ER
R.. The laser unit must be returned to the factory for any
service or repair. Service or repair must be handled by authorized factory
trained technicians.
Do not open the laser unit except to change batteries.
R
RE
EM
MO
OV
VE
E B
BA
AT
TT
TE
ER
RIIE
ES
S IIF
F T
TH
HE
E L
LE
EV
VE
EL
L IIS
S T
TO
O B
BE
E S
ST
TO
OR
RE
ED
D F
FO
OR
R A
AN
NY
Y L
LE
EN
NG
GT
TH
H O
OF
F
T
TIIM
ME
E.. Batteries may leak and damage the laser if it is stored idle for more than
3 months.
Be careful with this tool. Striking or jarring it, especially on the laser housing,
can affect its accuracy.
Other than batteries, there are no user-serviceable parts in the laser device.
ALIGNING THE LASER
The laser must be aligned with the blade before use. If the laser is not aligned
properly, your cuts will not be accurate.
TO ALIGN THE LASER:
1. The trigger switch and the
laser switch must be in the
OFF position.
2. Put a padlock or screwdriver
through the hole in the
trigger switch to make sure
the blade cannot be started
accidentally.
3. Plug in the power cord.
4. Turn on the laser switch.
5. Loosen the laser cover screws and
pull off the laser cover, leaving the screws in place.
6. Loosen the screws on the laser unit until it can be moved easily.
7.
Align the laser light line with either the left or right side of
the blade. Make sure the light is right against the blade. Extra space between
the laser line and the blade will lead to inaccurate cutting.
8. Once the laser light line is properly positioned, tighten the laser unit screws.
9. Push the laser cover back into place and tighten the laser cover screws.
Laser light should be kept OFF when not in use.
OPERATING INSTRUCTIONS FOR THE MITER SAW
Do not use the Miter Saw if the power cord (or extension
cord, if used) is worn, cut, or damaged in any other way. A worn or damaged
power cord must be replaced immediately. Contact Alltrade Customer
Service to obtain the proper replacement power cord. Failure to adhere to
this warning could result in damage to the Miter Saw motor, fire, or severe
electrical shock or even death to the operator.
LASER LIGHT
DO NOT VIEW DIRECTLY WITH OPTICAL
INSTRUMENTS (MAGNIFIERS)
CLASS 2M LASER PRODUCT
635-660nm, <1mW CW
CLASSIFIED PER IEC 60825-1, Ed. 1.2, 2001-08
AVOID EXPOSURE -
LASER LIGHT IS EMITTED
FROM THIS APERTURE.
LASER RADIATION
CAUTION LABEL
ALIGNING THE LASER