Kenwood TK-7180 - Manual (Page 2)

ADS#44207 Printed in USA
JQA-QMA1205
■ KMC-35
Microphone
(supplied microphone)
■ KMC-36
Keypad Microphone
■ KMC-9C
Control Station
Desktop Microphone
■ KRK-10
Control Head
Remote Kit (23ft/7m)
■ KCT-46
Ignition Sense Cable
■ KCT-40
Radio Interface Cable
(for KDS-100, KGP-2A/2B)
■ KCT-23M
DC Cable (Dash
mount / 10 feet)
■ KCT-23M3
DC Cable (Remote
mount / 23 feet)
■ KAP-2
Horn Alert/Public
Address Relay Unit
■ VGS-1
Voice Guide &
Storage Unit
■ KES-3
External Speaker
■ KES-5
External Speaker
(requires KAP-2)
■ KMB-10
Key Lock Adapter
■ KLF-2
Line Noise Filter
■ KPS-10A
DC Power Supply
■ KPS-15
DC Power Supply
■ KDS-100
Mobile Data Terminal
■ KGP-2A/2B
GPS Receiver /
Modem Unit
(requires KCT-39 option)
All accessories and options may not be available in all markets.
Contact an authorized Kenwood dealer for details and complete list of all accessories and options.
Model TK-7180 TK-7180H TK-8180 TK-8180H
GENERAL
Frequency Range
Type 1 136~174 MHz 450~520 MHz 450~512 MHz
Type 2 – 400~470 MHz
Number of Channels*
Zone Max.128 per Radio
Ch/GID Max.250 per Zones
(Max.512 [Conv.Ch’s +GID’s] total per Radio)
Channel Spacing
Wide 25 kHz, 30 kHz 25 kHz
Narrow 12.5 kHz, 15 kHz 12.5 kHz
Operating Voltage 13.6 V DC±15 %
Current Drain
Standby 0.4 A 0.4 A 0.4 A 0.4 A
Receive 1.0 A 1.0 A 1.0 A 1.0 A
Transmit 9.0 A 13.0 A 9.0 A 13.0 A
Duty Cycle Transmit: 20 %
Operating Temperature Range -22 ºF ~ +140 ºF (-30 ºC ~ +60 ºC)
Frequency Stability ±0.00025 % (-22 ºF ~ +140 ºF)
Antenna Impedance 50 Ω
Channel Frequency Spread
Type 1 38 MHz 70 MHz
Type 2 – 70 MHz
Dimensions (W x H x D), 6-5/16” x 1-3/4” x 6-3/16”
Projections not included (160 mm x 45 mm x 157 mm)
Weight (net) 3.3 lbs. (1.5 kg)
FCC ID
Type 1 K4437303110 K4437303210 K4437313110 K4437313210
Type 2– – – K4437313120 K4437313220
IC Certification
Type 1 282F-37303110 – – –
Type 2– – – 282F-37313120 –
Model TK-7180 TK-7180H TK-8180 TK-8180H
RECEIVER (Measurements made per EIA/TIA-603)
Sensitivity (12dB SINAD)
Wide 0.25 µV
Narrow 0.28 µV
Selectivity**
Wide 80 dB 80 dB
Narrow 70 dB 67 dB
Intermodulation Distortion
Wide/Narrow 75 dB (±50, 100 kHz)
Spurious Response** 90 dB 85 dB
Audio Output
(4
Ω Impedance) 4 W with less than 5 % distortion
TRANSMITTER (Measurements made per EIA/TIA-603)
RF Output Power
Type 1 30 to 1 W 50 to 10 W 30 to 1 W 45 to 10 W
(490 -520 MHz:25 to 1 W) (490 -512 MHz:40 to 10 W)
Type 2 – – 30 to 1 W 45 to 10 W
Spurious Response 70 dB
Type of Emission
Wide 16K0F3E
Narrow 11K0F3E
FM Hum & Noise
Wide 50 dB
Narrow 45 dB
Microphone Impedance 600 Ω
Audio Distortion
Wide/Narrow 3 %
Standard MIL 810C MIL 810D MIL 810E MIL 810F
Methods/Procedures Methods/Procedures Methods/Procedures Methods/Procedures
Low Pressure 500.1/Procedure I 500.2/Procedure I, II 500.3/Procedure I, II 500.4/Procedure I, II
High Temperature 501.1/Procedure I, II 501.2/Procedure I, II 501.3/Procedure I, II 501.4/Procedure I, II
Low Temperature 502.1/Procedure I 502.2/Procedure I, II 502.3/Procedure I, II 502.4/Procedure I, II
Temperature Shock 503.1/Procedure I 503.2/Procedure I 503.3/Procedure I 503.4/Procedure I, II
Solar Radiation 505.1/Procedure I 505.2/Procedure I 505.3/Procedure I 505.4/Procedure I
Rain 506.1/Procedure I, II 506.2/Procedure I, II 506.3/Procedure I, II 506.4/Procedure I, III
Humidity 507.1/Procedure I, II 507.2/Procedure II, III 507.3/Procedure II, III 507.4
Salt Fog 509.1/Procedure I 509.2/Procedure I 509.3/Procedure I 509.4
Dust 510.1/Procedure I 510.2/Procedure I 510.3/Procedure I 510.4/Procedure I, III
Vibration 514.2/Procedure VIII, X 514.3/Procedure I 514.4/Procedure I 514.5/Procedure I
Shock 516.2/Procedure I, II, III, V 516.3/Procedure I, IV, V 516.4/Procedure I, IV, V 516.5/Procedure I, IV, V
International Protection Standard
Dust & Water Protection P54: Radio itself
P54/55: Remote Head with KRK-10
*To meet above Mil810 and IP grade, weather proof microphone KMC-35 or KMC-36 has to be connected.
*Maximum capability depends on the number of programmed Zone and repeater channels.
** Typical specifications
Kenwood follows a policy of continuous
advancement in development. For this reason
specifications may be changed without
notice.
Options
Specifications
Applicable MIL-STD & IP
footnotes from Front:
1 KRK-10 remote control kit required.
2 DTMF includes PTT ID, Emergency ANI, Manual Encode (KMC-36),
Auto-Dial (9 numbers) & Stun.
3 Special Alert Tone Patterns operate for 2-Tone, DTMF,
FleetSync
® selective call decode.
4 Call Key: 6 keys max.; operates for 2-Tone, DTMF and
FleetSync status encode.
5 DB-25 ACC supports 15 Remote Zone/CH/GID selections,
KGP-2A/B (KCT-40 required), KDS-100 (KCT-40 required), data
modem, MDT, interconnect.
6 KCT-46 ignition sense cable option required; plugs into mobile
ignition sense pig-tail cable.
7 KAP-2 required: Horn Alert operates for FleetSync ® , 2-Tone or
DTMF selective call decode.
8 KPG-89D required: Windows ® 98/ NT/ 2000/ Me/XP compatible;
English/Spanish screen languages.
9 MIL-STD “Driven-Rain” and IP-55 Water/Dust Intrusion apply
to remote control head only; IP54 applies to radio chassis.
10 Conventional Zones: 512 Channels /128 Zones max. per radio;
250 CH max. per Zone Trunked Zones: 512 GID / 128 Zones
max. per radio; 250 GID max. per Zone.
11 Two-Tone Decode (4 sets x 4 pairs each); Single / Two-Tone
Encode (32 tones), Operator Selectable Tone (40 QT.DQT code pairs).
12 Kenwood LTR ® Features include: GID Delete/Add, LTR ® Talk
Around /Scan Revert Group Display, System Scan, Group Scan,
Auto Search.
13 FleetSync ® & FleetSync ® II are not compatible.
14 Short Text Messages are radio stored & LCD displayed; Long
Text Messages require a KDS-100 and KCT-40.
15 FleetSync ® GPS features require an internal GPS board or
externally wired GPS receiver with NMEA TTL level serial data
output to the internal COM 1 or 2 set to "GPS".
16 Requires a VGS-1 option.
FleetSync ® is a registered trademark of
Kenwood Corporation.
LTR
® is a registered trademark of Transcrypt
International.
GPS-2A
GPS-2B