Kodak 9020 - Manual (Page 20)

37
Connectors and
Interfaces Electrical System
P-Bus-in and P-Bus-out:
The following pin connections are used for
data transmission:
Pin 2: Transmit Data TxD
Pin 3: Receive Data RxD
Pin 5: Signal ground
9 8 7 6
External:
• P-Bus-in
9-pin Sub-D female connector (V.24/V.28
standard interface)
• P-Bus-out
9-pin Sub D male connector (V.24/V.28
standard interface).
• Slot for modules
• 8-pin remote socket (MiniDIN)
ADDRESS Switch
Rotary switch to set projector
address 1-16 (hex.-code 0-9
and A-H).
Slide Change Time:
0.88 sec (independent of mains voltage
and frequency).
Slide Access Times :
<3.5 sec for the longest search run.
Control system
5 4 3 2 1
Power Voltage: AC ONLY!
Different power voltages are adjustable via
the removable fuse link.
(120, 220, 230, 240 V)
Frequency:
50/60 Hz
Performance:
approximately 380 W
Fuses:
Primary circuit:
1 x T 2A L/250V for 220, 230 and 240V or 1
x 4 A slow blow/250V for 120V
Secondary circuit:
For 10 V:
1 x T 1.25 A L/250V (5 x 20 mm)
(For USA and Canada: 1 x 1.25 A slow blow/
250V)
For 24 V:
1 x T 2.0 A L/250V (5 x 20 mm)
(For USA and Canada: 1 x T 2.8 A slow
blow/250V)
Supply Voltage for External Units:
Provision of 12V/50 mA (DC) direct voltage
on the 8-pin remote control socket.
Provision of 24V/750 mA direct voltage or
34V/750 mA (AC) alternating voltage on
the slot for external control modules.
EKTAPRO 7020/9020 Projectors:
The P-Bus-in interface is used as exit to the
SLAVE projector. By setting of a transport
command via IR-remote or via a built-in
timer, a status call follows.
Slot for Module:
Pin a1: SDA Pin b1: SCL
Pin a2: - Pin b2: PLL_DISS
Pin a3: SLOT_232_R Pin b3: SLOT_232_T
Pin a5: SLOT_A
Pin b4: STBY_DIS
Pin a6: SLOT_C Pin b5: SLOT_B
Pin a8: 12 VDC Pin b6: SL_DISS
Pin a9: 34 VDC Pin b8: VSS 12
Pin a10:24 VAC_N Pin b9: VSS 34
Pin b10: 24 VAC_L
8-pin Standard Projector Socket:
(For connecting the KODAK EKTAPRO
Remote Systems or KODAK EKTAPRO
Twin Socket Adapter).
Pin 1: 12 VDC
Pin 2: Gnd
Pin 3: Signal 1 (LSB)
Pin 4: Signal 2
Pin 5: Signal 3
Pin 6: Signal 4
Pin 7: Signal 5 (MSB)
Pin 8: Interrupt
a10 a9 a8 a7 a6 a5 a4 a3 a2 a1
b10 b9 b8 b7 b6 b5 b4 b3 b2 b1
5
1 2
3
4
6
7
8
KODAK, CAROUSEL, TRANSVUE, EKTA-
GRAPHIC and EKTAPRO are registered
trademarks.