Kenwood KPA-H2EC - Manual (Page 2)

Step 1: Placing the Base and Cradle
First, determine where you want to mount Here2Everywhere. There are two
options for installing the Here2Everywhere. Select the option and location
that provides good visibility of and access to Here2Everywhere's front
panel while maintaining a safe driving experience.
Option 1: Windshield Mount
• Do not install Here2Everywhere on the windshield if it may obstruct your view while driving.
• Attach the Car Docking Cradle to the Car Windshield Docking Base using the four enclosed screws.
• Loosen the base nut on the Car Windshield Docking Base so that the suction cup portion rotates easily. Do not remove the base nut entirely.
• Make sure the suction cup lever is in the up position.
• Position the suction cup base on the desired windshield location. The word "PRESS" should be upright.
• Press the button marked "PRESS" while the suction cup is on the windshield. Then rotate the lever down, keeping the button pressed down at the same time.
• The suction cup base should be firmly attached to the windshield.
Note: To remove the Car Windshield Docking Base, return the lever to the up position before attempting to remove the Base.
Option 2: Console (Professional) Mount
Ask the dealer where you purchased your KPA-H2EC about professional installation options. One option is to have the dealer mount the Pivot of the Car Windshield Docking Base to the console
or other available location in the vehicle. There are four screws to remove. The Pivot screw holes match the AMPS standard for mounting systems, so any AMPS-compatible bracket for your vehi-
cle will accept the Pivot of the Docking Base. Many car audio dealers carry these brackets.
If you choose to do the Console mount yourself, please observe the following guidelines:
• Do not install Here2Everywhere where it may obstruct your view through the windshield or your view of your vehicle's indicator displays.
• Do not install Here2Everywhere where it will hinder your access to the vehicle's controls.
• Do not install Here2Everywhere where it may hinder the function of safety devices such as an airbag. Doing so may prevent the air-bag from functioning properly in the event of an accident.
• Find a location that provides good visibility of and access to Here2Everywhere's front panel.
• If using the four enclosed screws, be sure that you do not damage wiring or other systems that may be close to the mounting surface.
• Prior to mounting the Pivot, attach the Car Docking Cradle to the Pivot using the four enclosed screws.
Step 2: Attaching Power in a Vehicle
You have two options for powering the Here2Everywhere in your vehicle:
Plug the cigarette lighter adapter into the back of the cradle, as shown. Don't plug the adapter into the cigarette lighter until the installation is completed.
Or, wire the Extra Power Supply Cord with Fuse to the vehicle +12V battery line. Use caution in wiring to your vehicle's electrical system. Kenwood recommends
having a professional audio installer perform this step.
Step 3: Connecting Audio
Tune your vehicle radio to an unused FM station, and using the FM Transmitter Options feature on the Here2Everywhere menu, select the same
station frequency. When using Here2Everywhere, make sure you've tuned to the same station as you have previously set in the Menu setup.
(Refer to your Here2Everywhere manual.)
Tip: The Here2Everywhere also has a Wired FM Output. If you experience noise or other audio, you may want to have a professional installer add a connection from the Wired FM Output to the car
antenna input. Consult your car audio dealer or professional installer for assistance.
Step 4: Installing the Antenna
1. Turn Here2Everywhere's power off and remove it from the cradle; unplug the cigarette lighter adapter from the cigarette lighter; unplug the antenna from the cradle.
2. Find an antenna location on a metal surface at least 12" x 12." The antenna should be mounted exactly 5.5" (the length of the antenna's tail) away from the vehicle's rear window. The
antenna's powerful magnets will secure it to the metal surface. There is an optional antenna cable protector, or tail, included with the car antenna.
Note: The best reception is achieved when the antenna is mounted on the roof; mounting on the trunk lid will work for convertibles. If the vehicle has a roof rack or skid ribs, it may be necessary
to mount the antenna off-center.
3. Route the cable from the lowest point of the rear window into the trunk. Take advantage of any existing cable channels or wiring conduits.
For SUVs, Minivans & 5-door Vehicles: Bring the cable into the vehicle under the rubber molding for the tailgate, and continue under the interior trim.
4. From the trunk, route the cable around the passenger compartment and to the back of the cradle.
• Do not pull the cable across sharp edges that could damage it.
• Keep the cable away from areas where it could become tangled in driver's and passenger's feet.
5. Plug the antenna into the back of the cradle.
6. Confirm that the antenna is mounted in a good location.
• Make sure the vehicle is not in a garage, or somewhere the satellite signal could be blocked
• Temporarily plug the cigarette lighter adapter into the cigarette lighter.
• Slide Here2Everywhere all the way into the cradle so that the connector at the bottom of the unit makes proper contact in the cradle. Press the power ( ) button to turn Here2Everywhere on.
Note: KENWOOD RECOMMENDS UNPLUGGING THE CIGARETTE LIGHTER ADAPTER AFTER YOU TURN OFF THE VEHICLE'S IGNITION. (In some vehicles, the cigarette lighter remains active after
the ignition has been turned off, and leaving H2E's cigarette lighter adapter plugged into the cigarette lighter could drain the vehicle's battery.)
If your Here2Everywhere has been properly connected and the antenna is receiving the SIRIUS signal (Preview Channel #184)
you will hear audio. If you do not hear audio, the display will read "Acquiring Signal." Refer to your Here2Everywhere Instruction
Manual for details on how to operate your Here2Everywhere SIRIUS tuner. If you have not activated your SIRIUS satellite radio,
call 888-539-SIRIUS to subscribe.
Audio output (560 ohms). . . . . . . . . . . . . . . . 776mV RMS
Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3A fast blow
Power supply requirements . . . . . . . . . . . . . . 9 ~ 16V, negative ground
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . 110mm(L) x 74mm(W) x 30mm(D)
DC12V Audio Out FM Out
ANT
www.kenwoodusa.com
www.kenwoodusa.com/inquiry
1-800-KENWOOD
Main Office
P.O. Box 22745
Long Beach, CA 90801-5745
Canada Office
6070 Kestrel Road
Mississuga, Ontario L5T 1S8
Hawaii Office
Kenwood USA Corporation
P.O. Box 903
Pearl City, HI 96782
©2004 Kenwood USA Corporation. All Rights Reserved.