More pattern editing – KORG ER-1 User Manual
Page 4
ER-1 EasyStart
4.
Press STOP
Ä
press to select Part 2 key (it will light), then select either Smooth or TrigHold as type of Motion
Sequence
Ä
press REC
Ä
press PLAY to record
Ä
toggle Reverse key off / on, to record new Motion sequence for part
2
Ä
press STOP
Ä
press WRITE 2x to write pattern with the two new Motion sequences.
!
Each time you record a new knob or switch change with the Motion sequence function, it will OVERWRITE the previous
Motion sequence for that part. If you’re not satisfied with the Motion Sequence you just recorded, simply re-record it, or
Clear the Motion Sequence. One Motion sequence, using one knob rotation can be recorded for each Part. Two knob
rotations can be recorded for the Delay Motion Sequence (See the Owner’s Manual, page 18, and 28 for more
information)
5.
Record an Delay Motion sequence in the current pattern: In the Delay section, press the Motion Sequence key ( it
will light)
Ä
press REC
Ä
press PLAY
Ä
tweak the Delay Depth and Time knobs simultaneously to record the Delay
Motion sequence.
More Pattern editing:
Copy the previous pattern and change the pattern length:
1.
Select pattern d.64
Ä
press WRITE
Ä
rotate DIAL to select pattern d.63
Ä
press WRITE again, to copy pattern d.64 to
d.63. Don't PLAY pattern yet…
Ä
hold down Shift to see the pattern’s length. (One of keys 1-4 lights accordingly)
Ä
while holding Shift press an unlit key between 1 and 4 to change the pattern length to this new value.
View the step data in the pattern:
2.
While pattern plays, press each part key, and note that the step keys light to indicate where each part is set to trigger
along the 16-step grid
Ä
watch Select LED section (above step keys). Note that green LED indicates movement through
- and loops from bars 1-2.
3.
Continue playback of pattern
Ä
press Part 4key (it will light)
Ä
press Select> key 1x – the red LED in Select section
moves to 2
nd
bar in pattern
Ä
press Select< key 1x to move back to 1
st
bar. Note that you are viewing Trigger Settings
for the two different measures of Part 4. Press the HI-HAT Close key, so that it lights.
Edit the trigger settings for HI-HAT Close:
4.
Press Select < or > keys until bar 1's red LED is lit - to view the trigger settings for HI-HATpart, bar 1. Let the pattern
continue to play
Ä
press all of the lit keys to turn them OFF. Listen as pattern loops - when bar 1 plays again, no steps
will play - the rest of the data for the HI-HAT stays the same - for bar 2
Ä
press Select > key to move to bar 2
Ä
press
any desired step keys to change trigger settings for the HI-HAT, bar 2
Ä
press the STOP key.
Work with the Swing function:
5.
Select pattern A.14
Ä
PLAY pattern to hear how it sounds
Ä
press STOP
Ä
hold down the Shift key and press step
key 8 (Swing) - a value of 50 will flash in the display
Ä
rotate the DIAL to a setting of "69"
Ä
press step key 8 again
(flashing), to set new Swing value
Ä
PLAY pattern to hear new swing setting
Ä
STOP pattern
Ä
hold down Shift and
press step key 8.
6.
Rotate DIAL to set value to "50"
Ä
press step key 8 again to re-set Swing value
Ä
PLAY pattern again - to hear
"straight" 16-beat pattern
Ä
press STOP.
4