Lennox Hearth AKM-LSM LSM40ST-PV - Manual (Page 2)

LENNOX HEARTH PRODUCTS • ANDIRON KIT FOR MONTEBELLO ® GAS FIREPLACES • INSTALLATION INSTRUCTIONS
Printed in U.S.A. © 2011 Lennox Hearth Products
P/N 750183m Rev. A 04/2011
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Lennox Hearth Products reserves the right to make changes at any time, without notice, in
design, materials, specifications, and prices, and to discontinue colors, styles, and products.
Consult your local distributor for fireplace code information.
1508 Elm Hill Pike, Suite 108 • Nashville, TN 37210
Figure 5
2
Step 3. Fireplace models LSm40-2, LSm45-2, LSm40-PV, LSm45PV:
Remove the front three logs indicated in Figure 3.
Note: Logs are FRAGILE! Handle with care to prevent breakage.
For fireplace models LSm40ST and LSm40ST-PV: Log removal
is not necessary.
To install andirons in montebello Front View fireplace models
LSm40-2, LSm45-2, LSm40-PV and LSm45PV:
1) Loosen thumbscrews by turning them counterclockwise (do not
remove thumbscrews).
2) Place andirons onto grate as shown above in Detail A and B.
3) Turn thumbscrews clockwise until snug (do not overtighten). Also
see Figure 5.
To install andirons in montebello See-Through fireplace models
LSm40ST and LSm40ST-PV:
1) Remove thumbscrews by turning them counterclockwise. Discard
thumbscrews.
2) Place andirons onto grate as shown above in Detail A. Also see
Figure 6.
Thumbscrew
Andirons (Classic style shown)
Grate Assembly
Figure 4: Installing Andirons
Grate Assembly
DETAIL A
~
~
Figure 6
Figure 3
Fireplace models LSM40-2, LSM45-2, LSM40-PV, LSM45-PV:
Remove front three logs before installing andirons.
Step 4. Install andirons as described in Figure 4.
Step 5. Fireplace models LSm40-2, LSm45-2, LSm40-PV, LSm45PV:
Reinstall the logs removed in Step 3. For details, refer to the log
placement instructions in the fireplace Installation Instructions.
Note: Logs are FRAGILE! Handle with care to prevent breakage.
Step 6. See Figure 2.Reinstall the front glass door assembly, as follows:
a. Retrieve the glass door assembly. Visually inspect the gasket
on the backside of the frame to ensure it is clean, free of
irregularities, and firmly seated on the frame.
b. Position the door assembly in front of the firebox opening
with the top of the door held away from the fireplace, as
shown in Figure 2. Lower the bottom of the door assembly
onto the bottom door track. Pivot the door up after engaging
and centering in the base channel.
c. Using a Phillips screwdriver, fasten the door frame to the
door latch with the two (2) latch screws removed in Step 2.
WARNING: Risk of personal injury or property
damage. To prevent glass door assembly from falling out,
securely tighten latch screws when reinstalling. (Also see
WARNING box on Page 1.)
Step 7. If applicable, reinstall the mesh pull screen assembly removed
in Step 1, as follows:
a. Reattach both mesh pull screens to the rod.
b. Insert the right side of the rod into the corresponding hole
on the upper right side of the firebox opening.
c. Insert the left side of the rod into the corresponding hole on
the upper left side of the firebox opening.
Classic Andirons (2 sets) Installed in See-Through Fireplace
mission Andirons Installed in Front View Fireplace
mesh Pull Screens
DETAIL b
Andiron
(Classic style)
(Side View)