Linear DXS-63 - Manual

DXS-62
DXS-63
SUPERVISED
EMERGENCY
TRANSMITTERS
Operation Instructions
PRODUCT DESCRIPTION
The Models DXS-62 and DXS-63 are battery powered, miniature,
water-resistant*, supervised transmitters designed for use in emergency
applications with Linear’s DX and DXS Format receivers. Each is supplied
with a wristband, a pocket clip, and a Nylon pendant necklace. Pressing
buttons on either transmitter sends a digital coded wireless signal to its
companion receiver. To insure sending a complete signal,
press the transmitter button(s) for a minimum of two
seconds.
Each DXS transmitter is factory set to a unique code, so no fi eld coding
is required. The one-button DXS-62 sends a signal when its button is
pressed. The two-button DXS-63 transmitter sends a signal when both
buttons are pressed together. These transmitters can send a signal for
up to 30seconds per activation. The red signal indicator on the transmitter
lights and a built-in sounder beeps when the unit is activated.
If status transmissions are enabled, they will be sent every two hours.
Some receivers are able to use these signals, others are not.
Every two hours the transmitter tests for a low battery. This test takes
place even if status transmissions have not been enabled. If the battery
tests low, the transmitter sounder will beep and a low battery signal will
be sent.
Receivers must be programmed to the transmitter’s code before system
testing and operation. Refer to the receiver’s instructions for details on
operation and programming.
Each transmitter is sealed to provide water-resistance. The unit’s battery
is not replaceable. The transmitter should be discarded at the end of its
battery life.
* NOTE: Water resistance not tested by UL
FEATURES
WRISTBAND INSTALLATION PENDANT HOLDER INSTALLATION POCKET CLIP INSTALLATION
STATUS OPTION & PROGRAMMING SYSTEM TESTING LINEAR LIMITED WARRANTY
This Linear product is warranted against defects in material and workmanship for twenty-
four (24) months. The Warranty Expiration Date is labeled on the product. This warranty
extends only to wholesale customers who buy direct from Linear or through Linear’s
normal distribution channels. Linear does not warrant this product to consumers. Consumers
should inquire from their selling dealer as to the nature of the dealer’s warranty, if any. There
are no obligations or liabilities on the part of Linear
Corporation for consequential
damages arising out of or in connection with use or performance of this product or
other indirect damages with respect to loss of property, revenue, or profi t, or cost of
removal, installation, or reinstallation. All implied warranties, including implied warranties
for merchantability and implied warranties for fi tness, are valid only until Warranty Expiration
Date as labeled on the product. This Linear Corporation Warranty is in lieu of all other
warranties express or implied.
All products returned for warranty service require a Return Product Authorization Number
(RPA#). Contact Linear Technical Services at 1-800-421-1587 for an RPA# and other
important details.
IMPORTANT !!!
Linear radio controls provide a reliable communications link and fi ll an important need in
portable wireless signaling. However, there are some limitations which must be observed.
✴ For U.S. installations only: The radios are required to comply with FCC Rules and
Regulations as Part 15 devices. As such, they have limited transmitter power and
therefore limited range.
✴ A receiver cannot respond to more than one transmitted signal at a time and may be
blocked by radio signals that occur on or near their operating frequencies, regardless of
code settings.
✴ Changes or modifi cations to the device may void FCC compliance.
Infrequently used radio links should be tested regularly to protect against undetected
interference or fault.
✴ A general knowledge of radio and its vagaries should be gained prior to acting as a
wholesale distributor or dealer, and these facts should be communicated to the ultimate
users.
✴ This device complies with FCC Part 15 and Canada Rules and Regulations. Operation
is subject to the following two conditions: (1) This device may not cause harmful
interference and (2) this device must accept any interference received,
including interference that may cause undesired operation.
(760) 438-7000 • FAX (760) 438-7043
USA & Canada (800) 421-1587 & (800) 392-0123
Toll Free FAX (800) 468-1340
www.linearcorp.com
Copyright © 2003 Linear Corporation 215549 F
NOTE: NECKLACE SIDE OF PENDANT HOLDER
FITS CLOSEST TO THE SIGNAL INDICATOR
TO INSTALL PENDANT HOLDER, SLIDE HOLDER
INTO SLOTS ON ENDS OF TRANSMITTER
INSTALL THE PENDANT HOLDER
THEN CUT AND REMOVE THE NECKLACE
SNAP THE POCKET CLIP
INTO THE PENDANT HOLDER
BEEP... BEEP...
BEEP... BEEP... BEEP
IF THE FOUR HOUR STATUS TIMER IS REQUIRED FOR
SUPERVISION, PERMANENTLY ENABLE THE TIMER BY
PRESSING THE TRANSMITTER BUTTON FIVE TIMES IN
SUCCESSION (USE THE LEFT BUTTON ON DXS-63). THE DXS-62
WILL BEEP AFTER EACH BUTTON PRESS, THE DXS-63 WILL
NOT. FIVE BEEPS WILL SOUND WHEN THE TIMER IS ENABLED.
PROGRAM THE TRANSMITTER INTO THE RECEIVER BY
PLACING THE RECEIVER INTO PROGRAM MODE, THEN SEND
A SIGNAL TO THE RECEIVER FROM THE TRANSMITTER.
REFER TO THE RECEIVER'S PROGRAMMING INSTRUCTIONS
FOR DETAILS.
NOTE: THE END OF STRAP WITH VELCRO ATTACHES
TO THE END CLOSEST TO THE SIGNAL INDICATOR
TO INSTALL WRISTBAND, SLIDE STRAPS
INTO SLOTS ON ENDS OF TRANSMITTER
BEEP...
IMPORTANT! TEST SYSTEM WEEKLY
The manufacturer strongly recommends that you test
security equipment frequently. Over a period of time, no
electronic products are better than the inspection and
maintenence they receive. Therefore, from the time of
installation, it is absolutely necessary to test the system
at least once a week.
PLACE THE RECEIVER IN A "TEST"
MODE AND ACTIVATE THE
TRANSMITTTER. VERIFY THAT THE
SIGNAL IS RECEIVED AND THAT THE
SYSTEM REPORTS AS REQUIRED.
DXS-62
DXS-63
ACTIVATION
BUTTON
SIGNAL
INDICATOR
ACTIVATION
BUTTONS
(PRESS BOTH)
PENDANT HOLDER
NYLON
NECKLACE
POCKET
CLIP
WRIST
STRAP
PRINTER’S INSTRUCTIONS:
INSTR,INST,DXS-62/63 - LINEAR P/N: 215549 F - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 8.500” X 11.000” - SCALE: 1-1
BY