Land Pride RTR25 - Manual (Page 157)

Revision Comments Part Description Part No. Ref.
Drawing Image Number dwg11076
Rev. 2 (S/N 444064+) GBOX 700MM 1.5:1 RTA/RTR2555 826-426C 1.
Rev. 1 (S/N 444063-) GEARBOX ASSY 700MM RTR2555 311-263S 1.
Rev. 2 (S/N 440590+) RPBY 311-629A RTR2562 826-427C 1.
Rev. 1 (S/N 440589-) GEARBOX ASSY 800MM RTR2562 311-264S 1.
TOP BRACE WELDMENT RTR2555 311-257H 2.
TOP BRACE WELDMENT RTR2562 311-258H 2.
WASHER FLAT 5/8 SAE PLT 804-021C 3.
WASHER LOCK SPRING 5/8 PLT 804-022C 4.
HHCS 5/8-11X1 1/4 GR5 802-050C 5.
Rev. 2 not compat. w/Rev. 1 (S/N 148242+) RHSSNB 1/2-13 X 1 1/2 GR5 802-477C 6.
Rev. 1 (S/N 148241-) HHCS 1/2-13X1 1/2 GR5 802-091C 6.
WASHER FLAT 1/2 SAE PLT 804-016C 7.
NUT HEX 3/8-16 PLT 803-014C 8.
WASHER LOCK SPRING 3/8 PLT 804-013C 9.
GEARBOX GASKET RTA25/35 816-095C 10.
CHAIN GUARD WELDMENT RTA25/35 311-098H 11.
GASKET CHAIN GRD RTA25/35 816-092C 12.
Rev. 2 HFSS 1/4-20X7/8 GR5 802-719C 13.
Rev. 1 HFSS 1/4-20X3/4 GR5 802-257C 13.
DRAIN PLUG 3/4-16 UNF PLATED 800-066C 14.
FILL PLUG VENTED 3/4-16 PLT 800-094C 15.
HHCS 5/8-11X4 GR5 FTHD 802-286C 16.
NUT HEX JAM 5/8-11 PLT 803-023C 17.
CHAIN IDLER ARM RTA25/35 311-203D 18.
SNAP RING EXT .591 800-074C 19.
CHAIN TIGHTNER PIVOT RTA25/35 311-200D 20.
NUT HEX FLANGE 5/8-18 PLT 803-089C 21.
NUT LOCK 1/4-20 PLT 803-007C 22.
Rev. 2 not compat. w/Rev. 1 (S/N 148242+) RHSNB 3/8-16X1 1/4 GR5 802-155C 23.
Rev. 1 (S/N 148241-) HHCS 3/8-16X1 1/4 GR5 802-079C 23.
Rev. 2 RTR2555 (S/N 444064 +) RTR2562
(S/N 440590+) SPKT 9T #100 12/24X20T SPLINE 808-350C 24.
Rev. 1 RTR2555 (S/N 444063-) RTR2562
(S/N 440589-) SPKT 11T #100 12/24X20T SPLINE 808-102C 24.
NUT LT JAM 1 1/2-12 NYLN INSRT 803-111C 25.
SPKT 14T #100 12/24X20T SPLINE 808-104C 26.
Rev. 2 RTR2555 (S/N 444064 +) RTR2562
(S/N 440590+) CHAIN RL#100X38P HIGH TENSILE 809-111C 27.
Rev. 1 CHAIN RL #100X39P HIGH TENSILE 809-126C 27.
#100 CONNECTOR LINK 809-097C 28.
SP TINE HHCS 1/2-20X1 1/4 GR5 802-248C 29.
WASHER LOCK SPRING 1/2 PLT 804-015C 30.
NUT HEX 1/2-20 PLT 803-018C 31.
55" = 21; 62" = 24 BLADE TILLER 25 SERIES RH 820-058C 32.
55" = 21; 62" = 24 BLADE TILLER 25 SERIES LH 820-057C 33.
ROTOR WELDMENT RTA/RTR2555 311-080H 34.
ROTOR WELDMENT RTA/RTR2562 311-081H 34.
SNAP RING INTERNAL 3.938 800-017C 35.
BEARING 309 822-079C 36.
GASKET RTA25/35 816-094C 37.
LH LOWER BRG MOUNT RTA25 311-197D 38.
NUT HEX 1/2-13 PLT 803-020C 39.
SEAL 2.25 X 3.5 X .438 816-091C 40.
SEAL 2 X 3.1875 X 0.469 816-084C 41.
RH BEARING MOUNT RTA25 311-196D 42.
15 TILLER LH BOTTOM BRG GASKET 816-071C 43.
BEARING 308 822-084C 44.
06/13/13 RTA10, RTA15, RTA25, RTR25 & RTA35 Series Rotary Tiller 311-251P 157
Table of Contents Part Number Index
Section 3: Drives Land Pride
RTR25 SERIES
Drive
Applies to RTR2555, RTR2562