Legacy Car Audio LCD87DFX - Manual (Page 4)

BASIC OPERATION
CAUTION: Do not install the detachable panel before connecting the wire.
1. The unit is designed for negative terminal of the battery which is connected
to the vehicle metal. Please confirm it before installation.
2. If the car interior is extremely hot, as after being parked in the sun, do not
use the player until the car has been driven for a while to cool off the interior.
3. Press the OPEN button to flip down the front panel (see fig.1), then take
away the front panel (see fig.2) and put it in the protective case (see fig.3)
safe keeping.
4. Install the front panel back into its bracket and then push it back to the
position for playing (see fig.4).
FRONT PANEL
OPEN BUTTON
( FIG.1)
FRONT PANEL
( FIG.2)
FRONT PANEL
PROTECTIVE CASE
INSTALLATION
3 8
1. OPEN BUTTON
Press it to flip down the front panel then you can insert the cd disc into the cd compartment
on the back of the front panel,press it to eject the disc.
Press SEL button to change the mode in the sequence of
A.The volume level can be adjusted at any time by pressing the audio level+ or - button as
select mode has been initially defaulted at volume mode.
The volume level is also obtained by stepping through the SEL button until the function
VOL is displayed and then press + or - button to adjust the sound level.
C.Press SEL button hold for more than 2 seconds and select + or - button can have a beep sound.
A. During CD mode, press button allow you to track forwards.
Hold the button allow you to skip forwards.
B. During Mp3 mode, press button allow you to track forwards.
Hold the button allow you to skip forwards.
Press it to select your desired radio band and the band which is selected will be displayed
on LCD.
Press it hold for more than 2 seconds can have LOUD mode.
LOUD MODE:
When reduce the volume to half level, press it to enhance the bass effect.
For Mp3 playing(MP3 model only), this button can act as the
key.
Press it to display time on LCD for few seconds.Press it hold and then press or
button to adjust hour or minute.
Press it to turn on or off the unit.
(for RDS model only)
AF [ALTERNATIVE FREQUENCIES](For RDS only)
When pressed short, AF switching mode is selected and the state of AF switching mode is
displayed by AF segment in display
Segment off: AF switching mode off.
Segment on: AF switching mode on, and has RDS information.
Segment flashing: AF switching mode is selected, but RDS information is not received yet.
When AF switching mode is selected, the radio checks the signal strength of AF all the time.
The interval of checking time of each AFs depends on the signal strength of current station,
from a few minute for strong station to a few seconds for weak station. Everytime that new
AF is stronger than current station, it switches over to that frequency for very short time, and
NEW FREQUENCY is displayed for 1-2 second. Because the mute time of AF switching or
checking time is very short, it is almost inaudible in case of normal program.
EJ button
2.8.9 SEL( AUDIO MODE SELECT)/ +/- BUTTONS
3.10.TRACK UP /DOWN BUTTONS
4.BAND BUTTON
ENTER
5.CLOCK BUTTON
6.POWER BUTTON
7.AF BUTTON
B.Press sel button to select the BAS,TRE ,BAL,FAD then press +/-button to adjust tthem.
For Mp3 playing(MP3 model only), these two buttons act as the digit 8 & 9 key.
C. During RADIO mode, press and you can
manual search channel.Then press search channel.
hold or for more than 2 seconds
or , you can have auto
When pressed long, it is activated of regional mode on /off .
Regional mode ON
AF switching or PI SEEK is implemented to the station which have all PI codes are the
same as current station.
REG of individual segment is turned on also together with displaying REG ON numeric
VOL BAS TRE BAL FAD
(Volume) (Bass) (Treble) (Balance) (Fader)