Land Pride ZXT72 Pro - Manual (Page 2)

2 Manual No. 357-274M 4/19/10
Assembly Instructions
■
Folding ROPS Bar Assembly
Refer to Figure 2:
1.
Do not remove 1/2" hydraulic hoses (#14) from
expansion tanks (#13).Unsrew hex nuts (#12) and
move expansion tanks (#13) to the side.
2. Do not remove rear bumper (#11) from mower frame.
Remove existing bumper bolts (#5B).
3. Insert lower right hand ROPS tube (#9) in mounting
bracket “A”. Make sure hinge at the top faces back.
4. From the rear, insert 1/2" x 3 1/4" GR5 hex head cap
screw (#5B) through mounting bracket “A” and
ROPS tube (#9) as shown. Secure with 1/2" lock
nut (#6B). Draw lock nut up snug, do not tighten.
5. From the front, insert 1/2" x 3 1/4" GR5 hex head cap
screw (#5A) through mounting bracket “A” and
ROPS tube (#9) as shown. Secure with 1/2" lock
nut (#6A). Draw lock nut up snug, do not tighten.
6. Repeat steps 3, 4 & 5 above to install lower left hand
ROPS tube (#8) in mounting bracket “B”.
7. Attach upper ROPS tube (#10) to lower right ROPS
tube (#9) with 1/2" x 3 1/4" GR5 cap screw (#5) and
hex lock nut (#7). Draw hex lock nut (#7) up snug, do
not tighten.
8. Attach upper ROPS tube (#10) and ROPS stop (#3)
to the lower left ROPS tube (#8) with 1/2" x 3 3/4"
GR5 cap screw (#4) and hex lock nut (#7). Draw hex
lock nut (#8) up snug, do not tighten.
9. Tighten hex lock nuts (#6A & #6B) to 76 ft-lbs.
10. Rotate ROPS loop end (#10) up and insert locking
pins (#2). Secure locking pins with hair pin clips
attached to locking pins.
11. Install locking knobs (#1) and hand tighten.
12. Reattach expansion tanks (#13) to side plates with
existing hex flange top lock nuts (#12). Tighten hex
flange top lock nuts (#12) to 8 ft-lbs.
Folding ROPS Bar Assembly
Figure 2
25971
1 to 6 . . . . . . Figure 1 . . . . 357-420A . . . . RETRASCTABLE SEAT BELT KIT, Z-MOWERS . . . . . . . . . . . . . 1
1 . . . . . . . . . Figure 2 . . . . 230024700 . . . LOCKING KNOB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2 . . . . . . . . . Figure 2 . . . . 230311900 . . . PIN, ROPS HINGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
3 . . . . . . . . . . Figure 2 . . . . 711834101 . . . ROPS STOP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
4 . . . . . . . . . . Figure 2 . . . . 802-042C . . . . HHCS 1/2-13 X 3 3/4 GR5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
5 . . . . . . . . . Figure 2 . . . . 802-099C . . . . HHCS 1/2-13 X 3 1/4 GR5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
6 . . . . . . . . . Figure 2 . . . . 803-019C . . . . NUT LOCK 1/2-13 PLT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
7 . . . . . . . . . Figure 2 . . . . 803-019C . . . . NUT LOCK 1/2-13 PLT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
8, 9, & 10 . . . Figure 2 . . . . 823-287C . . . . ZXT FOLDING ROPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . . . . . 357-274M . . . . INSTRUCTION, ZXT ROPS INSTALLATION . . . . . . . . . . . . . . . . 1
Kit No. 357-273A Folding ROPS W/Seat Belt, ZXT Pro Series
Items Figure No. Part No. Part Description Qty
Corporate Office: P.O. Box 5060
Salina, Kansas 67402-5060 USA
www.landpride.com