Lexmark 10N0026 - Manual (Page 2)

—All except 10N0026
-1- -2-
—ONLY 10N0026
CONTENTS:
CONTENTS:
1. Protect work surface.
Refilling your cartridge is a clean and simple job, but it is best to cover your
work area with newspaper or other scrap paper to protect from accidental
ink spills.
2. Remove depleted color print cartridge from printer
according to printer manufacturer's instructions.
3. Lay cartridge on its side. CAREFULLY using the razor knife provided
in the kit, work the blade into the joint between the green cap and black
cartridge body on all four sides to pry off cap. See Fig. 1.
4. Remove the scabbard from the refill dispenser of the color
you wish to refill. Insert the filler tube into the corresponding color
compartment through either of the two fill holes. Determine
appropriate color chamber by following figure 2. Push the filler tube
into the absorbent material as far as it will go. Then draw it back
out about 1/4" (6.5mm). See Fig. 2
5. Tilt the bottle until the filler tube is in the fully inverted
position Fig. 3. Squeeze the bottle with moderate pressure and keep
pressure applied until you see ink appear at the top of the color
compartment. Immediately stop squeezing the bottle. Draw filler tube most
of the way out then release pressure on bottle and allow the refill bottle to
suck back any excess ink.
6. Bring the bottle back to the position shown in Fig. 2
(filler tube in horizontal position) and remove the filler tube.
Recap the ink bottle and save for future refills. Replace the cap
on the print cartridge and tape into place with pressure sensitive
Scotch Tape . See Fig. 4. Inspect the print head and wipe off
any excess ink immediately to prevent possible contamination
of print nozzles.
7. Reinstall the cartridge into the printer.
If asked “Installing a new cartridge” or “Reinstalling a used cartridge,”
choose “Installing a new cartridge.” This will reset the ink level
monitor to read “Full.” Run a priming/cleaning cycle and print test
following the instructions included with your printer. It may be
necessary to repeat the print test several times to bring the color
balance back to normal.
Ink Dispensers
Cyan/Magenta/Yellow
3 x 15cc
1 Cap
Removal Tool
Pry off cap with
blade tool supplied
Fig. 2
Cyan
Yellow
Magenta
CONTAINS SHARP BLADE
KEEP KIT AND TOOL
OUT OF REACH OF
CHILDREN
Ink Dispensers
Cyan/Magenta/Yellow
3 x 15cc
1 Cap
Removal Tool
for Lexmark 10N0026 Tri-Color Cartridge ONLY
Pry off cap with
blade tool supplied
1. Protect work surface.
Refilling your cartridge is a clean and simple job, but it is
best to cover your work area with newspaper or other
scrap paper to protect from accidental ink spills.
2. Remove depleted color print cartridge from printer
according to printer manufacturer's instructions.
3. Lay cartridge on its side. CAREFULLY using the razor
knife provided in the kit, work the blade into the joint
between the green cap and black cartridge body on all four
sides to pry off cap. See Fig. 1.
4. Remove the scabbard from the refill dispenser of the
color you wish to refill. Insert the filler tube into the corresponding
color compartment through either of the two fill holes. Determine
appropriate color chamber by following figure 2. Push the filler tube
into the absorbent material as far as it will go. Then draw it back
out about 1/4" (6.5mm). See Fig. 2
5. Tilt the bottle until the filler tube is in the fully inverted
position Fig. 3. Squeeze the bottle with moderate pressure
and keep pressure applied until you see ink appear at the top of
the color compartment. Immediately stop squeezing the bottle.
Draw filler tube most of the way out then release pressure on
bottle and allow the refill bottle to suck back any excess ink.
6. Bring the bottle back to the position shown in Fig. 2
(filler tube in horizontal position) and remove the filler tube.
Recap the ink bottle and save for future refills. Replace the cap
on the print cartridge and tape into place with pressure sensitive
Scotch Tape see Fig. 4. Inspect the print head and wipe off
any excess ink immediately to prevent possible contamination
of print nozzles.
7. Reinstall the cartridge into the printer.
If asked “Installing a new cartridge” or “Reinstalling a used
cartridge,” choose “Installing a new cartridge.” This will reset
the ink level monitor to read “Full.” Run a priming/cleaning
cycle and print test following the instructions included with
your printer. It may be necessary to repeat the print test several
times to bring the color balance back to normal.
Fig.4
13806 19
4076
Color
Print
Cartridge TM
Fig. 4
Place pressure
sensitve
Scotch Tape
firmly on
cartridge cap
Pressur e Sensitive Tape
Fig. 3
Dispense ink
into selected
color chamber
Cyan
Yellow
Magenta
Yellow
Cyan
Magenta
Dispense ink
into selected
color chamber
Fig. 3
Yellow
Cyan
Magenta
TM
Place pressure
sensitve
Scotch Tape
firmly on
cartridge cap
Pressur e Sensitive
Tape
CONTAINS SHARP BLADE
KEEP KIT AND TOOL
OUT OF REACH OF
CHILDREN
LX80RC 5/02
Fig. 1
Fig. 1
Fig. 2
Refilling Instructions Refilling Instructions
for Lexmark 12A1980/12A1985/15M0120/15M0125/17G0060/16G0065;
Compaq 337710-001; Xerox 8R7880/8R7882/8R12591
and Sharp AJ-C50C Tri-Color Cartridges
TM
TM