Lincoln Electric WELDMARK IM806 - Manual (Page 23)

C-1 ACCESSORIES C-1
WELDMARK 225
OPTIONAL EQUIPMENT
(Field Installed)
K957-1 HEAVY DUTY, TWO WHEEL TRAILER FOR
SMALL WELDERS - For road, off-road and in-plant
and yard towing. (For highway use, consult applicable
federal, state and local laws regarding requirements
for brakes, lights, fenders, etc.). Order:
K957-1 Trailer
K958-1 Ball Hitch
K958-2 Lunette Eye Hitch
K959-2 Fender & Light Kit
K965-1 Cable Storage Rack
K889-2 & -3 Two-Wheel Undercarriage - For moving
by hand. Overall Width 29 in (.74m) Both have pneu-
matic tires. Puncture proof tires included with K889-3.
K1631-1 Puncture Proof Wheel Kit - For converting
K889-2 to puncture proof pneumatic tires.
K893-1 Caster for Undercarriage - Mounts to the
front of the K889-2 to allow easy movement on
smooth surfaces. Includes 6
” diameter hard rubber
wheel and convenient toe-on, toe-off locking brake.
K933-1 Four Wheel Undercarriage - For Hand
Moving. Rear pneumatic tires, front molded wheels.
K934-1 Cylinder Brackets - For use with K933-1. for
transporting either one LPG fuel cylinder or one weld-
ing gas cylinder.
K1737-1 FOUR WHEEL ALL-TERRAIN UNDER-
CARRIAGE - For moving by hand at construction
sites. Heavy duty puncture resistant pneumatic tires.
K1770-1 UNDERCARRIAGE (FACTORY) - For mov-
ing by hand on a smooth surface. One or two gas
cylinders can be mounted on the rear of the undercar-
riage with the installation of K1745-1 Cylinder
Holder(s). Heavy duty puncture resistant pneumatic
tires and front caster.
K1745-1 SINGLE GAS CYLINDER HOLDER
For use on K1770-1 Undercarriage. One or two may
be installed on an undercarriage.
K1788-1 ROLL CAGE - Gives added damage protection.
K886-1 Canvas Cover -To protect the Weldmark 225
when not in use. Made from attractive red canvas
material which is flame retardant, mildew resistant,
and water repellent.
K802-R Power Plug Kit - Provides four 115V plugs rated at
15 amps each and one dual voltage, full KVA plug rated at
115/230V, 50 amps.
K802-N Power Plug Kit - Provides four 115V plugs
rated at 20 amps each and one dual voltage, full KVA
plug rated at 115/230V, 50 amps. (For K1418-2 or
K1419-2 CSA machines and machines with GFCI recep-
tacles, use K802-R).
K704 Accessory Kit - Includes 35 ft (10.7m) 2/0 AWG elec-
trode cable, 30 ft. (9.1m) 2/0 AWG work cable, headshield with
No. 12 filter, GC300 work clamp and Cooltong
® 300 electrode
holder. Cables are rated at 300 amps, 100% duty cycle.
K892-1 Remote Control Receptacle Kit - Includes a 6-pin
MS-type (Amphenol) receptacle and a local-remote toggle
switch that mounts in the case front. Required when using a
K930-2 Tig Module with an optional Amptrol or when using a
Remote Control.
K857 25 ft (7.5m) or K857-1 100 ft. (30.4m) REMOTE CON-
TROL - Portable control provides same dial range as the output
control on the welder. Has a convenient 6 pin plug for easy
connection to the welder.
K894-1 Spark Arrester Kit - Includes a heavy gauge steel,
approved spark arrester and clamp for easy mounting to muffler
exhaust pipe.
K1690-1 GFCI Receptacle Kit - Includes two UL approved
120V ground fault circuit interrupter duplex type receptacles
with covers and installation instructions. Replaces the two fac-
tory installed 120V duplex receptacles. Each receptacle of each
GFCI duplex is rated at 20 amps, but the maximum total current
from each GFCI duplex is limited to 20 amps. Two kits are
required. See the MAINTENANCE section for detailed
information on testing and resetting the GFCI receptacle.
K930-2 TIG Module - Provides high frequency and shielding
gas control for AC and DC GTAW (TIG) welding applications.
Its compact case is designed for easy carrying, complete with a
handle. High frequency bypass is built in. The K938-1
Contactor Kit must be field installed in the TIG Module when
used with a Weldmark 225. Additionally, the K936-3 control
cable is required if remote control is used. If remote control is
not used the K936-4 control cable is required.
K936-3 Remote Control Cable - Control cable for connecting
the K930-2 TIG Module to a Weldmark 225 equipped with a
K892-1 Remote Kit. 9-Socket to a grounded 115 V plug and a 6
pin MS-connector. (Contains circuits 2, 4, 31, 32, 75, 76, 77
and ground)
K939-1 Docking Kit - For mounting the K930-2 TIG Module
unit on top of the Weldmark 225.
K1816-1 FULL KVA ADAPTER KIT - Plugs into the 120/240V
NEMA 14-50R receptacle on the case front (which accepts 4-
prong plugs) and converts it to a NEMA 6-50R receptacle,
(which accepts 3-prong plugs.)