Lincoln Electric NA-5 IM305-C - Manual (Page 143)

A Motor and Gear Box Assembly See P-101-R
B Control Panel Assembly See P-101-O
1 Carriage Frame G1384 1 X X X
2 Upper Guide Wheel Assembly, Includes: T5335-1 4 X • •
2 Upper Guide Wheel Assembly, Includes: T13876 4 • X •
2 Upper Guide Wheel Assembly, Includes: T13875 4 • • X
Shaft T10647 1 X • •
Shaft S15558 1 • X X
Bearing M9300-6 1 X X •
Bearing M9300-67 1 • • X
Retaining Ring S9776-50 2 • X X
3 Roll Pin T9967-43 4 • X X
Lockwasher - Guide Wheel Mounting E106A-5 6 X • •
Washer - Guide Wheel Mounting S9262-1 8 X • •
5 Lower Bearing Bar Assembly S10299 2 X • •
5 Lower Bearing Bar Assembly M12980-2 2 • X •
5 Lower Bearing Bar Assembly M12980-1 2 • • X
6 Spacer - Thin S10262-1 ø 4 X • •
6 Spacer - Thin S10262-5 4 • X X
7 Spacer - Thick S10262-2 ø 8 X • •
7 Spacer - Thick S10262-4 2 • X •
Lockwasher, Lower Bearing Bar Mounting E106A-4 4 X • •
9 Socket Head Screw T9447-14 ø 4 X • •
9 Socket Head Screw T9447-49 2 • X X
C Head Mounting and Lift L3116 1 X • •
C Head Mounting and Lift L5460 1 • X X
Head Mounting Parts See P-101-Q 1 X X X
19 Lift Handle M8385 1 X • •
19 Lift Handle M12968 1 • X X
20 Lift Handle Stud T10652 1 X • •
20 Lift Handle Stud T13872 1 • X X
21 Set Screw, Lift Handle and Stud Mounting S11604-11 2 X • •
Hex Jam Nut, Locking Set Screw 3/8-16 1 X • •
21 Roll Pin, Lift Handle Mounting T9967-30 1 • X X
22 Roller, Mounts Item C thru Crank Bracket T8128 1 X X X
23 Gear Box Mounting Plate M8485 ø 1 X X X
24 Flat Head Screw 5/16-18 x .625 4 X X X
25 Drive Wheel T13586 1 X X X
Key, Drive Wheel to Motor M8776-6 1 X X X
Spacer S9262-44 1 X X X
Lockwasher T9860-2 1 X X X
26 Nut, Drive Wheel to Motor T10552 1 X X X
27 Swivel Motor Mount S10288 2 X X •
27 Swivel Motor Mount S15772 2 • • X
28 Oil Cup T8679 2 X X X
29 Hex Head Bolt 1/2-13 x 1.00 2 X • •
29 Hex Head Bolt 1/2-13 x 1.25 2 • X X
30 Lockwasher E106A-5 2 X X X
31 Upper Spring Bracket S10379 1 X X X
32 Hex Head Bolt 3/8-16 x .75 2 X X X
06-06-2001
For K23 & K236 Models (below code 7500), use the parts marked “X” in Column 1.
For K247 Models (above code 7500), use the parts marked “X” in Column 2.
For K247-HC Models (above code 7500), use the parts marked “X” in Column 3.
ITEM DESCRIPTION PART NO. QTY. 1 2 3 4 5 6 7 8 9
P-101-P.1.a
(Supersedes P-52-C.1)
P-101-P.1.a
(Supersedes P-52-C.1)
# Indicates a Change This Printing
Sub Assembly Illustration
Sub Assembly Illustration
Sub Assembly Illustration
Sub Assembly Illustration
ø
This part is obsolete and no longer available.
#