LG 20LH1DC1 - Manual (Page 62)

62
COMMERCIAL MODE
COMMER
CIAL MODE
Editing/Adding Channel ICONs and/or Labels
If there is no pre-assigned ICON, you can make a
channel label of up to 7 characters to help in identifying
the channel or network.
At your option, channel labels can also be added in
addition to a pre-assigned ICON. You may also add
labels for the Aux input sources to clearly identify the devices that are connected to the Aux inputs.
Editing and adding the labels can only be done if there
are channels entered into the 20LH1DC1’s channel map
either by using the method described in item 5 (page
62), by cloning or by the use of the master remote
control from the PPV provider.
To Do Channel Editing/Labeling, proceed as follows
1. Enter 20LH1DC1 Installer menu.
2. After the installer menu appears, press ‘2’, ‘5’, ‘4’,
‘MENU’.
This enters the channel label edit mode.
Add your channel icons and channel labels in this
menu, see below. (You can do this more than once.)
3. To exit the menu when done press “MENU”.
Adding Channel Icons and Labels in the 2-5-4 + Menu Mode
Changing a Channel’s ICON on
Master TV
1. With Channel Up/Down, select
the channel you want to change
the Icon for.
2. With the A A D D JJ F or G , select the
letter ‘I’ on the channel ID display.
3. With the A A D D JJ D or E , select the
desired ICON you want to appear
to identify the channel. (If you
know the ICON number, enter the
number followed by Enter /
Select.)
*Note: If no Icon is available, leave at or
select the default blank icon display.
4. Proceed with Changing/Adding
Labels orgo to the next channel.
Changing/Adding Channel Labels on
Master TV
1. Channel Up/Down to select the
desired channel.
2. Press the A A D D JJ F or G repeatedly
until the numbers 1 to 7 show
up. The number shows the
position of the character that can
be changed. Number 1 is the first
character, number 2 the second
character and so on.
3. With the A A D D JJ D or E , select the
desired character.
4. Proceed to the next number
position or use Channel Up/Down
to go to the next channel.
Changing Source Labels on Master
TV
1. Press “TV/AV” or “BANK” to
select the desired Aux input
source; Video 1, HDMI.
2. Press the A A D D JJ F or G repeatedly
until the numbers 0 to 9 show
up.
The number shows the position of
the character that can be
changed.
3. Use the A A D D JJ D or E to select
the desired character.
4. Press “TV/AV” or “BANK” for the
next Aux source or proceed with
Changing Icon or
Changing/Adding Labels.
• CHANNEL Up/Down - Tunes in the next channel in
scan.
• Left/Right Arrows - Select the item to change. If “I”
is shown, the ICON can be changed. If a number is
shown, it indicates the position of the character that
can be changed.
• Up/Down Arrows - Select the ICON or the character
to be displayed.
• 0 – 9 - Use to enter the index number of the ICON,
if known.
• OK (Enter/Select) - Changes the ICON after the
number has been entered.
• TV/AV (BANK) - Changes the Aux input label. This
key is located on side of set and on Installer remote
control.
• MENU - Exits the labeling/editing menu.
Installer Remote Control Key Functions for Master TV Channel Editing/Labeling Menu
1 2 3 4 5 6 7
XYZ
XYZ
XYZ
NETWORK
(Label)
(Icon)
PEFERENCE
Procedures for adding Channel Label Icons/Custom Channel Labels
(2-5-4 + MENU Mode)