LG SAC30708043 - Manual (Page 102)

COMMER
CIAL
MODE
SETUP
100
COMMERCIAL MODE SETUP
0=Broadcast, 1=CATV, 2=HRC, 3=IRC, 4=Same as NTSC.
103 - ATSC TUNE MODE
Sets ATSC tuning mode: Default set to 1 for Physical
channel scan.
Set to 0 for Virtual Channel scan.
104 - START MINOR CHANNEL
Sets XX-XX minor start channel number at power up:
0=NTSC. If not 0, number selected is the Minor start
channel number.
106 - ASP RATIO LOCK (Aspect Ratio Lock)
Set to 1 to retain previous aspect ratio with power Off.
Set to 0 to retain default aspect ratio with power Off.
See item 96 Default Aspect Ratio above.
116 - VIDEO MUTE EN (Video Mute Enable)
Set to 0 for normal.
Set to 1 for blank.
117 - FACT DEFAULT (Factory Default)
Set to 0 for normal.
Set to 1 to load presets to all of the previous item set-
tings.
WARNING: Setting this to 1 will reload the
factory defaults and clear the channel list
including erasing any assigned Channel Icons
and custom channel Labels.
118 - POWER SAVING
Default is set to 1, power saving mode is enabled.
Set to 0 to disable power saving mode.
■ Power Saving is only active when TV is in standby
mode.
■ Power Saving is not available in normal power on mode.
If Power Saving is disabled and TV is in Standby mode
with External card installed: TV can supply 12V (12
Watts) to External card and Sandby power consumption
will be normal.
119 - GEM STRT CH (Gem Start Channel)
Sets the Gem start channel. Set the channel number
that will provide Gem data to the TV at turn on. Initially
the TV may take several minutes to load program data
from AC power off state.
120 - PSEUDO PWR OFF (Pseudo Power Off)
Set to 0 to disable. If disabled, TV will take normal time
to turn On.
If enabled, simulates TV power off state for user (black
screen) and speeds up the apparent TV turn on time
(restores picture and sound). Set from 001 - 255 to
specify time TV will remain on but show a black screen
when power is pressed to turn TV off. In pseudo power
off state with TV on, pressing power turns backlight off
thus showing a black screen. TV is still active and can be
turned on quickly from pseudo power off state if Power
is pressed. Maximum time Pseudo Power Off can be
enabled is 4 minutes and 15 seconds.
087 - REAR RGB EN. (Rear RGB Enable)
Controls access to rear RGB input on TV.
Set to 0 to disable RGB input.
Set to 2 for PC for STB RGB input.
Set to 18 for Auto Configure one time only with power
cord removal and reinsertion.
088 - EN NOISE MUTE (Enable Noise Mute)
If set to 1, audio mutes if no signal is present.
090 - KEY LOCK
If set to 1, display panel keyboard is locked out, not
available to end user. IR receiver remains functional.
091 - YPrPb2 (HDMI2 Enable)
Set to 0 to disable display panel HDMI2 input.
Set to 1 to enable DTV mode. Set to 2 to enable PC
mode.
093 - RJP AVAILABLE
Set to 0, remote jack pack is not available.
Set to 1 HDMI mode, TV selects RJP’s HDMI port for
digital audio and video.
Set to 2 for DVI mode, TV selects RJP’s HDMI port for
digital video only - audio remains from last audio source.
094 - SAP MENU EN (2nd Audio Program)
Set to 1 to enable SAP feature on Function menu, if
Function menu is available.
Set to 0 to disable SAP feature on Function menu, if
Function menu is available.
096 - DEF. ASP. RATIO (Default Aspect Ratio)
Selects default aspect ratio at power up, see settings
below.
Set to 0 “Set By System”.
Set to 1 for 4:3.
Set to 2 for 16:9 (Factory Default).
Set to 3 for Horizon
Set to 4 for Zoom 1
Set to 5 for Zoom 2
099 - BACK LIGHTING
Sets the TV screen brightness at power up, see settings
below.
Default setting is 200.
1 - 100 Static Backlighting.
(1 = Dimmest picture, 100 = Brightest picture.)
101 - 200 Dynamic Backlighting.
(101 = Dimmest picture, 200 = Brightest picture.) If
settings are above 101, the TV automatically controls
backlighting depending upon the picture level of the
current program.
102 - ATSC BAND
Sets up TV to receive different types of incoming signals: