Lightolier Calculite HID Downlight C4T4VM - Manual

631 Airport Road, Fall River, MA 02720 • (508) 679-8131 • Fax (508) 674-4710
We reserve the right to change details of design, materials and finish.
www.lightolier.com © 2009 Philips Group • B0609
Job Information Type:
Job Name:
Cat. No.:
Lamp(s):
Notes:
Calculite ® HID Downlight
C4T4VM
Page 1 of 4 4½" Aperture, 2pc Vertical, T4 Medium Beam
Features
1. Upper Reflector: Clear anodized aluminum, 0.040" (16-ga.). Provides medium
beam optics ideal for general lighting. Also available in medium and wide
beam, see C4T4VN and C4T4VW specification sheets.
2. Aperture Cone: Provides 50° visual cut-off to lamp and lamp image; self-
flange in painted white or aperture-matching polished flange. Consult factory
for other finishes.
3. Lamp Shield: High-temperature glass as required by code, captive during
re-lamping. Light diffusion provides exceptionally smooth beam.
4. Socket Housing: Galvanized steel, pre-wired with G8.5 pulse rated socket.
Snaps onto upper reflector for secure attachment without tools; unitized
construction assures proper lamp alignment to optics for consistent performance.
5. Mounting Frame: 0.048" (18-ga.) galvanized steel. Vertical adjustment
mechanism accommodates mounting to virtually any ceiling system using
mounting bars (provided, or 1/2" EMT tubing (by others). Single locking feature
secures all adjustments. Alignment holes and markings allow fixture to be
preset prior to installation.
6. Mounting Ring: 0.048"(18-ga.) galvanized steel. Designed for vertical
adjustment from above or below for ceilings from 0" to 2" thick. Center-line
notches allow consistent alignment of multiple fixtures.
7. Mounting Bars: 0.048" (18-ga.) pre-installed, telescoping bars extend to
30" long and lock securely into position. Built-in locking tabs provide positive
attachment to common T-bar systems. Self-centering feature simplifies
installation in 24" O.C. grid systems. Attaches to steel or wood joists without
accessories.
8. Trim Retention Springs: Rust resistant springs secure reflector/housing for
quick, tool-less installation.
9. Ballast / Socket Housing / Cover Assembly: Snaps onto junction box
without tools for inspection and ballast replacement, accessible from below.
10. Junction Box: 0.048" (18-ga.) galvanized steel. UL listed for 8 No. 12 AWG,
90°C through branch circuit conductors. Allows inspection from below.
11. Thermal Protector: (Not Shown) Meets NEC and UL requirements. Do not
install insulation above nor within 3" (76mm) of any part of the luminaire.
Electrical
Electronic Ballast: 120 or 277V, 50/60 Hz., encased, high power
factor, T.H.D. <15%, thermally and transient protected, RMI/RFI complies with
FCC Part 18 non-consumer limits, shut-down circuit at end of lamp life, sound
rating “A”, -5°F minimum starting temperature, Type 1 Outdoor rating.
Ballast ANSI Code Voltage Max. Amps Input Watts
20W MH M156 120/277 0.21/0.10 23
39W MH M130 120/277 0.39/0.17 44
70W MH M139 120/277 0.67/0.29 78
Options and Accessories
Slope Ceiling Adapters: See Specification Sheet SCA.
Chicago Plenum: Consult Factory.
Labels
UL (Suitable for Damp Locations), CSA, I.B.E.W.
For 70W, install fixtures with minimum spacing between:
1. Center-to center of adjacent luminaries: 2 feet.
2. Top of luminaire to overhead building member: 1/2 inch.
3. Luminaire center to side building member: 1 foot.
Ceiling Cutout: 5 1/8” (130 mm) Dia.
Reflector Trim Frame-In Kit Lamp (Ceramic Metal Halide)
C4T4VM CLW
CLP
CCDW
CCDP
CCZW
CCZP
Specular Clear, White Painted Flange
Specular Clear, Matching Flange
Comfort Clear Diffuse, White Painted Flange
Comfort Clear Diffuse, Matching Flange
Champagne Bronze, White Painted Flange
Champagne Bronze, Matching Flange C420BT5PGJ5E1
C420T4GU65EU
C420T4EU
C439T4GU65EU
C439T4E1
C439T4E2
C470T4E1
C470T4E2 Electronic 120V
Electronic 120V/277V
Electronic 120V/277V
Electronic 120V/277V
Electronic 120V
Electronic 277V
Electronic 120V
Electronic 277V 22W Philips MiniMasterColor
20W GE ConstantColor
20W T4.5
39W Philips MiniMasterColor
39W T4.5
39W T4.5
70W T4.5
70W T4.5