Linear AM3Plus - Manual (Page 2)

2
Contents Introduction
The AM3Plus Access Controller is designed for use as a primary access
control device for gated communities, parking garages, offi ce buildings,
apartments, dormitories, hotels/motels, commercial buildings and
recreational facilities.
Housed in a lockable, plastic enclosure, the AM3Plus features a 2-digit
LED display, nine status indicators, four relay indicators with four relay
activation pushbuttons. Three programming buttons, a reset button,
and a power indicator are present. The enclosure is monitored with a
magnetic “tamper” switch.
The system controls its four output relays by responding to various input
devices that react to proximity cards, transmitters, and entry codes. The
four relay output channels can be programmed to control electric door
strikes, magnetic locks, door & gate operators, or barrier gates.
Access is granted or denied depending on the current user’s authorization
to gain access and system settings that control groups of users or all
users. Complete access control event logging, access time restriction,
access location restriction, and administration functions are also available
to manage the installation.
The AM3Plus is network ready. Multiple units can be interconnected
on a 3-wire RS-485 network or through modems. The AM3Plus can be
used in mixed networks with its sister products, the AE1000Plus and
AE2000Plus.
Two sets of Wiegand inputs are available for connection to 26, 30, or
31-bit Wiegand devices (card readers, etc.). Two sets of PBUS inputs are
available for connection to Linear’s line of remote accessories.
The AM3Plus can be powered from a 12-24 Volt AC or DC source. DC
power can be obtained from the access device or AC power from a
separate power transformer. The system supports and charges a 12-volt
backup battery for operation during power outage. Low battery detection
circuitry monitors the backup battery’s condition. The EEPROM memory
retains all entry codes and programming, even without power.
Operation
In a typical installation, the unit’s memory would be programmed with
each resident’s name and entry code number. Arriving visitors would use
a remote keypad to enter their entry code. Also proximity receivers, swipe
card readers, and other remote devices can be used with the system.
Block coded MegaCode® transmitters can be used to gain access
through a remote radio receiver connected to the AM3Plus PBUS. Each
transmitter can be individually suspended or re-activated.
The system’s clock/calendar can control access based on specifi c times
and dates. Automatic relay activation can be scheduled. Access can be
restricted to certain times and dates. Holiday access can be scheduled.
The system’s event log records system activity for future reference.
Programming and Cardholder Maintenance
Two programming methods can be used with the system: Linear’s
AXNET or AccessBase2000. Each has its advantages, but only one must
be chosen at the onset for each installation. Once a unit is programmed
with one method, all programming data will be lost if a decision is made
to switch to the other method.
Linear’s AXNET software is built into each unit. It allows connecting to the
unit using common browser software from any PC at any location. Each
unit’s database is stored in the unit’s memory.
Linear’s AccessBase2000 software installs in one dedicated PC and is
designed with many extra features usually for large network installations.
The database for the entire system is stored in the dedicated PC.
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Programming and Cardholder Maintenance . . . . . . . . . . . . . . 2
Hardware Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Software Highlights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Feature Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Accessory Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
PBUS Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Wiegand Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Component Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Important Mounting Requirements . . . . . . . . . . . . . . . . . . . . 7
AM3Plus Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Relay Output Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Power, Battery, & Ground Wiring . . . . . . . . . . . . . . . . . . . . . 10
Telephone Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
PBUS Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Wiegand Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
RS-232 Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Optional Network Connections . . . . . . . . . . . . . . . . . . . . . . .13
System Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
System Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Specifi cations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Linear Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
FCC Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Throughout this manual, multiple-unit networks are referenced. Depending on
the programming method used, networks can contain the following model units:
NETWORK MODEL OPTIONS
With AccessBase2000 Programming With AXNET Programming
AM3Plus AM3Plus
AE1000Plus AE1000Plus
AE2000Plus AE2000Plus
AM-3
AE-1000
AE-2000