Leisure Time LX20 - Manual (Page 22)

in a given eyepiece while in the FIELD menu. At power
up the RADIUS menu file option is set to 15 arc minutes,
the radius of 1/2 a degree (30 arc minutes), which is
about the proper setting for a 26mm eyepiece used in
an 8" f/10 LX200.
To calculate the true field of an eyepiece in the
telescope, first divide the focal length of the telescope
(e.g., 2000mm for an 8" f/10) by the focal length of the
eyepiece (the standard supplied eyepiece is a 26mm
Super Plossl, 2000 divided by 26 equals 77X
magnification). Then find the apparent field of the
eyepiece (which is 52 degrees for the 26mm Super
Plossl) and divide it by the magnification (52 divided by
77 equals 0.67 degrees, multiplied by 60 equals 40.2
arc minutes).
To get the radius of the true field of view, divide the true
field by 2. In the case of the above equation, 40.2 arc
minutes divided by 2 equals 20.1 arc minutes.
2. Mode Two: COORDINATES/GO TO
Mode Two allows you to see where you have pointed the LX200 in
two celestial coordinate formats, either R.A. and Dec. or
Altazimuth. Also in this mode you can enter new Right Ascension
and Declination coordinates for any sky position, perhaps to locate
objects not in the LX200 library such as comets or asteroids and
have your telescope slew to the new coordinates.
a. Coordinates Menu File
You will at first see the RA = and DEC = coordinates of where the
telescope is pointing. If you move the LX200 with the N, S, W, or E
keys, the coordinates display will immediately update the new
position in Right Ascension and Declination.
You can also display computed information of the Altazimuth
coordinates (ALT = and A2 =) by pressing the ENTER key. To
return to RA = and DEC =, press the ENTER key again.
The RA = display is broken down into hours, minutes, and tenths
of a minute, and the DEC = display is broken down into + for North
Declination and - for South Declination into degrees and minutes as
shown in Display 32:
If you have made an ALTAZ style of alignment, the ALT = and AZ =
coordinate display is formatted so that 0 degrees azimuth (AZ =) is
due South that increases to up to 359 degrees and 59 minutes
moving clockwise, or from due South moving Westerly, altitude
(ALT =) is formatted so that straight overhead is +90 degrees and
00 minutes, decreasing to +00 degrees, and 00 minutes as you
move the telescope level with the horizon, and then as the LX200
moves below +00.00 it will give minus altitude readings. The
Altazimuth coordinate display is shown in Display 33:
While in ALTAZ, you will find during slewing in one direction, that
both the RA = and DEC = display will change at the same time,
while the ALT = and the AZ = display will only change in the
direction that the telescope is being slewed. It is also important to
note that only the Declination setting circle (3, Fig. 1) will give a
correct reading. The R.A. setting circle (10, Fig. 1) will only give
correct readings in the POLAR setting (see APPENDIX B, page 29).
b. GO TO Menu Option
The GO TO menu option, allows you to enter new Right
Ascension and Declination coordinates of any object in the sky, so
that the LX200 will slew to the new position. With this ability,
your LX200 knows no bounds, any celestial object, including
comets, asteroids, etc. are easily found, provided you have
accurate coordinate data to refer to.
To enter a new pointing position in Right Ascension and
Declination, press the GO TO key and a double beep will be heard
followed by a blinking cursor that will appear over the RA =
coordinate numbers. At this point, type in the new Right Ascension
coordinate numbers, then press the ENTER key. You will then
notice that the blinking cursor is over the DEC = coordinate
numbers. Enter the new Declination coordinate numbers, then
press the ENTER key and the LX200 will slew to the new
coordinate position.
You can also slew to ALTAZ coordinates from the ALTAZ display
as described above.
If you need to enter a minus Declination setting, move the blinking
cursor over the + symbol with the W key and then press the NEXT
key to get the - (minus) symbol, then move the blinking cursor to
the first number with the E key and enter the new coordinate
numbers. If you are already at a minus (-) Declination setting and
wish to enter a plus (+) declination setting, follow the same
instructions as above but press the PREV key instead to get the +
symbol.
3. Mode Three: CLOCK/CALENDAR
The continuously operating clock and calendar is the life pulse of
your LX200. At power up, the telescope's sidereal clock
automatically allows the system computer to make orbital
calculations of the planets, and correct stellar precession for
superior pointing ability.
Your accurate initial input of local time and date, with its long-life
lithium battery back-up, need not be re-entered every time you
use the LX200, thus enhancing the user friendly aspects of the
instrument.
To set the local time and date and to enter the correct GMT offset
(see QUICK START, page 9). Be sure to use your local hour setting
appropriately in either 12 hour or 24 hour format as
predetermined by the 12/24 HOUR TELESCOPE menu file option.
The long-life lithium battery (Panasonic CR2032 3 vDC or Duracell
DL2032B) is stored behind the power panel of the Drive Base (see
Behind the Power Panel, page 53 for battery replacement
information).
4. Mode Four: TIMER/FREQ
a. TIMER = Menu Option
The TIMER = menu option is for accurately timing different
observing or imaging tasks for up to 12 hours long. Counting down
to zero, in the hours, minutes, and seconds format, it will give a
pleasant beeping tone to notify you that the time is up. To set the
TIMER, move the arrow to TIMER = 00:00:00. Then press and
hold the ENTER key to get the double beep tone and the blinking
cursor. Enter the number of hours, minutes, and seconds that you
require. If you need to correct an error in entry, use the E and W
keys to move the blinking cursor and then type in the correct
information. After entry, press the ENTER key again and the
cursor will delete. When you are ready to start your time count-
down, press the ENTER key once more. To pause the count-down
press ENTER again, and then again to resume.
If you want an automatic 12 hour countdown, press the ENTER
key without holding. Then press ENTER to countdown.
b. FREQ = Menu File
FREQ = (Frequency) allows you to adjust the tracking speed (not
slew speed) of the LX200 digitally in tenths of a hertz from 56.4 Hz
to 60.1 Hz, so that you can match virtually every celestial motion
in the sky. Some popular drive rate settings are:
22