Legacy Car Audio PRO LINE ML3215 - Manual (Page 6)

You can toggle between these settings with the up or down buttons. When the desired setting appears
on screen, press the MODE button. Under the RX Tone and TX tone settings, your choices toggle
between N NO O T TO ON NE E, , C CT TC CS SS S, , D DC CS S and I ID DC CS S (No Tone, Continuous Tone Coded Squelch System tones, Digitally
Coded Squelch tones and Invert Digitally Coded Squelch tones).
If you choose the CTCSS tone setting, you will need to use the up or down buttons to select the desired
tone code of 49 available. If you choose CTCSS code 1, your display will read: C CT TC CS SS S 0 01 1
If you choose CTCSS code 49, your display will read: C CT TC CS SS S 4 49 9
When the desired CTCSS tone code appears on the display, select and set your choice by pressing the
MODE button or the P-T-T. The radio will save your selection and return to standby mode.
CTCSS Tone Signaling Frequency Table
No. Freq. No. Freq. No. Freq. No. Freq. No. Freq.
01 67.0 11 97.4 21 136.5 31 192.8 41 171.3
02 71.912 100.0 22 141.3 32 203.5 42 177.3
03 74.4 13 103.5 23 146.2 33 210.7 43 183.5
04 77.0 14 107.2 24 151.4 34 218.1 44 189.9
05 79.7 15 110.9 25 156.7 35 225.7 45 196.6
06 82.5 16 1114.8 26 162.2 36 233.6 46 199.5
07 85.4 17 118.8 27 167.937 241.8 47 206.5
08 88.5 18 23.0 28 173.8 38 250.3 48 229.1
09 91.5 19 127.3 29 179.9 39 69.3 49 254.1
1 0 94.8 20 131.8 30 186.2 40 159.8
If you choose the DCS tone code setting, you will need to use the up or down buttons to select the
desired tone code of 105 available. If you choose DCS code 023, your display will read: D DC CS S 0 02 23 3
If you choose DCS code 754, your display will read: D DC CS S 7 75 54 4
When the desired DCS tone code appears on the display, select and set your choice by pressing the
MODE button or the P-T-T. The radio will save your selection and return to standby mode.
DCS Tone Signaling Frequency Table
DCS DCS DCS DCS DCS DCS DCS DCS DCS DCS DCS
Code Code Code Code Code Code Code Code Code Code Code
023 054 125 165 245 274 356 445 506 627 732
025 065 131 172 246 306 364 446 516 631 734
026 071 132 174 251 311 365 452 523 632 743
031 072 134 205 252 315 371 454 526 654 754
032 073 143 212 255 325 411 455 532 662
036 074 145 223 261 331 412 462 546 664
043 114 152 225 263 332 413 464 565 703
047 115 155 226 265 343 423 465 606 712
051 116 156 243 266 346 431 466 612 723
053 122 162 244 271 351 432 503 624 731
If you choose the IDCS tone code setting, you will need to use the up or down buttons to select the
desired tone code of 105 available. If you choose IDCS code 023, your display will read: I ID DC CS S 0 02 23 3
If you choose IDCS code 754, your display will read: I ID DC CS S 7 75 54 4
When the desired IDCS tone code appears on the display, select and set your choice by pressing the
MODE button or the P-T-T. The radio will save your selection and return to standby mode.
IDCS Tone Signaling Frequency Table
To set the per-channel radio transmit output power, press and release the MODE button, then the up or
down buttons until appears. Press the MODE button to select. Scroll through the sub-menu settings with the up
or down buttons, press the MODE button T TX X P PO OW WE ER R when appears. Settings include: P PW WR R H HI I
P PW WR R L LO O
You can toggle between these per-channel settings with the up or down buttons. When the desired
setting appears on screen, press the MODE button to select. The radio will save your selection, and return
to standby mode. The display will show an “H” or an “L” to confirm High (45 Watt) or Low (2 Watt)
output power setting for the current channel.
To set the normal scan list on/off setting, press and release the MODE button then the up or down
buttons until the C CH H S SE ET T display appears. Press and release the MODE button again to select. Scroll through
the sub-menu settings with the up or down buttons, press the MODE button when N No or r S SC CA AN N appears on
screen . N No or r S SC CA AN N appears. Settings include: N NS SC CA AN N O ON N
N NS SC CA AN N O OF F
You can toggle between these settings with the up or down buttons. When the desired setting appears
on screen, press the MODE button to select. The radio will save your On or Off selection for the current
channel, and return to standby mode.
NOTE: Your radio will only scan channels with the scan setting “On”.
To set the Priority scan list on/off setting, press and release the MODE button then the up or down
buttons until the C CH H S SE ET T display appears. Press and release the MODE button again to select. Scroll through
the sub-menu settings with the up or down buttons, press the MODE button when P PR RI I S SC CA AN N appears on
screen. Settings include: P PS SC CA AN N O ON N and P PS SC CA AN N O OF F .
You can toggle between these settings with the up or down buttons. When the desired setting appears
on screen, press the MODE button to select. The radio will save your On or Off selection for the current
channel, and return to standby mode.
NOTE: This setting is linked to the Priority Scan sub-menu in the “System Option” menu, detailed
following this section. “If Priority Scan option of “System Option” menu is on, Priority scan works only
when the channel selector is positioned to the channel with “PSCAN ON” displayed.”
ENGLISH
7
ENGLISH
8 IDCS
Code
754
743
734
732
731
723
712
703
664
662
IDCS
Code
654
632
631
627
624
612
606
565
546
532
IDCS
Code
526
523
516
506
503
466
465
464
462
455
IDCS
Code
454
452
446
445
432
431
423
413
412
411
IDCS
Code
371
365
364
356
351
346
343
332
331
325
IDCS
Code
315
311
306
274
271
266
265
263
261
255
IDCS
Code
252
251
246
245
244
243
226
225
223
212
IDCS
Code
202
174
172
165
162
156
155
152
145
143
IDCS
Code
134
132
131
125
122
116
115
114
074
073
IDCS
Code
072
071
065
054
053
051
047
043
036
032
IDCS
Code
031
026
025
023