Panasonic KX-P7100 - Manual (Page 3)

FOR USERS IN AUSTRALIA
This mark shows that the product complies with AS/NZS 3548.
N52
For Your Safety
General
Warning
To prevent fire or shock hazard, do not expose this product to rain or any type of
moisture.
Caution
Do not open covers and do not attempt to repair the unit yourself. Refer servicing to
qualified personnel.
Power Source
Warning
• The power source voltage of this unit is listed on the nameplate (located on the
rear of the printer). Only plug the unit into an outlet with the proper voltage. The
voltage level of the power source must not vary more than ±10% from the proper
voltage level.
• When you operate this equipment, the outlet should be near the equipment and
accessible.
• To ensure safe operation the AC cord supplied must be inserted into standard
three-prong AC outlet which is effectively grounded (earthed) through the normal
wiring.
• The fact that the equipment operates satisfactorily does not imply that the power
point is grounded (earthed) and that the installation is completely safe. For your
safety, if in any doubt about the effective grounding (earthing) of the power point,
consult a qualified electrician.
• If the plug cannot be inserted into the AC outlet, contact a licensed electrician to
replace the outlet with a properly grounded (earthed) one.
• Do not defeat the purpose of the grounding (earthing) plug (ex. do not use a
conversion plug).
• Do not use an extension cord.
Laser Safety
Caution
This printer utilizes a laser. Use of controls or adjustments or performance of
procedures other than those specified herein may result in hazardous laser
radiation exposure.
Laser diode properties
Laser output:
5 mW max
Wavelength: 785 nm
Emission duration: Continuous
Caution Labels
CLASS
KLASSE
CLASSE
CLASE
1 LASER PRODUCT
1 LASER PRODUKT
1 LASER PRODUIT
1 LÁSER PRODUCTO
(220-240 V equipment)
CAUTION
HOT SURFACE INSIDE
CAUTION
HOT SURFACE
FOR USERS IN U.K.
IMPORTANT:
FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY
This printer is supplied with a moulded three pin mains plug for your safety and
convenience. A 5 amp fuse is fitted in this plug. Should the fuse need to be replaced please
ensure that the replacement fuse has a rating of 5 amps and that it is approved by ASTA or
BSI to BS 1362.
Check for the ASTA mark or the BSI mark on the body of the fuse.
If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse
is replaced.
If you lose the fuse cover the plug must not be used until a replacement cover is obtained.
A replacement fuse cover can be purchased from your local Panasonic Dealer.
IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET IN
YOUR HOME THEN THE FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF AND
DISPOSED OF SAFELY. THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF
THE CUT OFF PLUG IS INSERTED INTO ANY 13 AMP SOCKET.
If a new plug is to be fitted please observe the wiring code as shown below.
If in any doubt please consult a qualified electrician.
WARNING: THIS APPLIANCE MUST BE EARTHED.
IMPORTANT: The wires in this mains lead are coloured in accordance with the following
code.
Green-and-Yellow: Earth Blue: Neutral Brown: Live
As the colours of the wire in the mains lead of this appliance may not correspond with the
coloured markings identifying the terminals in your plug, proceed as follows.
The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the
plug which is marked with the letter E or by the Earth symbol , or coloured GREEN or
GREEN-AND-YELLOW.
The wire which is coloured BLUE must be connected to the terminal in the plug which is
marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal in the plug which is
marked with the letter L or coloured RED.
How to replace the fuse: Open the fuse compartment with a screwdriver and replace the
fuse.
ASA
L N
SCREWDRIVER
FUSE COVER
FUSE
Ozone Release
Warning
Make sure that the printer is installed in a well ventilated room so as not to increase
density of ozone in the air. Since ozone is heavier than air, it is recommended that
air at floor level be ventilated.
FOR USERS IN UNITED STATES
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to
radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
· Reorient or relocate the receiving antenna.
· Increase the separation between the equipment and receiver.
· Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
· Consult the dealer or an experienced radio/TV technician for help.
The user may find the booklet “Something About Interference” available from FCC local
regional offices helpful.
FCC Warning: To assure continued FCC emission limit compliance, the user must use the
recommended shielded interfacing cable when connecting to a host computer. Also, any
unauthorized changes or modifications to this equipment would void the user’s authority to
operate this device.
FCC Declaration of Conformity
Trade Name : Panasonic
Model Number : KX-P7100
Responsible Party: Matsushita Electric Corporation of America
One Panasonic Way
Secaucus, NJ 07094 U.S.A.
Telephone No.: 1-800-726-2797
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Technical Support Calls
If you have read this manual and tried the troubleshooting procedures and you are still
having difficulty, please contact the reseller from which the unit was purchased. You may
also call the end user technical support telephone number which is operational during East
Coast business hours (9:00 AM to 7:00 PM).
The end user technical support number is 1-800-PANASYS.
This number is available within the U.S. only.
( 220 - 240 V equipment)
A certified power supply cord has to be used with this equipment. The relevant
national installation and/or equipment regulations shall be considered. A certified
power supply cord not lighter than ordinary polyvinyl chloride flexible cord according
to IEC 60227 (designation H05VV-F 3G 0.75 mm 2 or 1.0 mm 2 ).