Pyramid Technologies PA-1000DJ - Manual (Page 4)

Connecting
to
standard AC power
After makin� all other connections, set the POWER switch
to OFF positIon. Then connect the power cord to a standard
AC outlet.
the amplifier
This is designed to accept standard rack mounting
installations. Two slots on each end of the front panel make
it suitable for such an installation.
secure four mounting screws (not supplied) through
these slots and into your standard electronics equipment
rack.
Turning the amplifier on
1. Tum on the audio inp'ut source equipment which is
connected to the amplifier INPUT jacks.
2. Set the amplifier's Channell and Channel 2 output level
gain controls to the minimum level settings.
3. Push in the power switch to turn the amplifier on.
Using the power LED meters (WIthout PA-600DJ)
The meter pointer position indIcates the amplifier output
power. For ease of reading in dark environments, the meter
IS illuminated.
Caring for your Pyramid PA Amplifier
Your Pyramid
PA
Amplifier is an example of superior design
and craftsmanship. The following suggestions will help you
care for your amplifier so you can enjoy years of use:
•
Keep the dry. If it wet, immediately.
•
Use the only in installations.
•
Handle the amplifier gently and do not dropl
•
Keep the amplifier away from dust and
•
Wipe occasionally with a damp cloth to it looking
new. Do not use harsh chemicals, or
detergents!
Using the Channel 1 and Channel 2 Output Level controls
Rotate output level gain clockwise to increase, or counter·
clockwise to decrease the output power. To get the best
performance with the least sound distortion, always adjust
the output level gain so the meters pointer does not
continuously exceed the extreme right of the meters scale.
CAUTION: It is possible to overdrive the amplifier by
setting output level gain too high, which may cause
damage or failure.
Amplifier Speclftcatlons PA·600DJ PA·800DJ PA·l000DJ PA·2000DJ
Input Impedance, balanced (unbalanced) 20 k·Ohms (10 k·Ohms) 20 k·Ohms (10 k·Ohms) 20 k·Ohms (10 k·Ohms)
Continuous Output Power
Stereo Mode
20 Hz to 20 kHz, 8 Ohms
1 kHz, 4 Ohms
Maxtmum Power, a Ohms
Maxtmum Power, 4 Ohms
Peak Power, 8 Ohms
Bridged Mode
20 Hz to 20 kHz, 8 Ohms
1 kHz, 8 Ohms
Peak Power
THO at rated output power
Frequency Response +/- 3 dB
Input Sensitivity for rated output power
Slgnal·to·Nolse Ratio A·Wefghted
Speaker Impedance
Stereo
Bridged
Power Requirement
Dimensions
H x W x DJ inches
(mm)
Weight, lb. (kg)
7(N{x 2
10000x 2
II(N{x2
13(N{x2
6O(N{x 2
l40Wx 1
l40Wx 1
120(N{ xl
0.1%
10 Hz to 50 kHz
I.OY
100 dB
4·16 Ohms
8·16 Ohms
3 15132 X 19 x 10 3/4
(88 X 482 x 273)
18.7 (8.5)
4· PYRAMID PA·600DJ/800DJ/l000DJI2000DJ Amplifier OWner's Manual
12(N{x 2 17OWx2
l60Wx 2 llOWx2
17(N{x 2 23OWx2
20(N{x 2 27OWx2
800Wx2 l000wx2
240Wx 1 340Wx 1
240Wx 1 340Wx 1
200(N{x 1 3000wx 1
0.1% 0.1%
10 Hz to 50 kHz 10 Hz to 50 kHz
I.OY I.OY
100 dB 100 dB
4·16 Ohms 4·16 Ohms
8·16 Ohms 8·16 Ohms
120 VAC, 60 Hz I 230 VAC, 50 Hz
53116X19X1131132 53116X19X1131131
(132 x 482 x 304) (132 x 482 x 304)
22.88 (10.4) 24.64 (11.2)
20 k·Ohms (10 k·Ohms)
20OWx2
24OWx2
26(N{x2
27(N{x2
180(N{x2
400Wx 1
400Wx 1
4000Wx 1
0.1%
10 Hz to 50 kHz
I.OY
100 dB
4·16 Ohms
8·16 Ohms
53/16X19X11 ]1131
(132 x 482 x 304)
25.08 (11.4)