Using multi operations, Using system off, Controlling components – Pioneer Elite SC-35 User Manual
Page 88: Using multi operations using system off, Followed by this receiver
Controlling the rest of your system (In case of SC-37)
10
88
En
8
Repeat steps 5 to 7 to program a sequence of up to
commands.
9
When you’re finished, use
/ to select ‘EDIT
EXIT’ from the menu and press ENTER.
You will return to the remote control Setup menu. Select
EXIT SETUP to exit.
Using multi operations
You can start multi operations with the receiver switched
on, or in standby.
1
Press MULTI OPERATION.
MULTI OPERATE flashes in the display.
2
Press an input function button that has been set up
with a multi operation.
The receiver switches on (if it was in standby) and the
programmed multi operation is performed
automatically.
1
Using System off
1
Press MULTI OPERATION.
MULTI OPERATE flashes in the display.
2
Press
SOURCE.
The command sequence you programmed will run, then
all Pioneer components will switch off
2
, followed by this
receiver.
3
Controlling components
This remote control can control components after
entering the proper codes (see Selecting preset codes
directly on page 84). Set the remote control operation
selector switch to SOURCE, then press the input function
buttons to select the component.
• TV CONTROL on the remote control are dedicated to
control the TV assigned to the TV operation selector
switch. If you have two TVs, assign the main TV to the
TV operation selector switch.
Note
1 With this remote control, the IR and RF modes can be selected separately for the individual input functions. To perform a multi operation on
a device (input function) for which the IR mode is selected, point the remote control toward the remote sensor on that device.
2 In order to avoid accidently switching off a DVD recorder that is currently recording, no DVD recorder power off codes are sent.
3 • With this remote control, the IR and RF modes can be selected separately for the individual input functions. To turn off the power of a device
(input function) for which the IR mode is selected using the System Off function, point the remote control toward the remote sensor on that device.
• When the power code of another brand is registered, the power on/off operation may be inverted. When using the System Off function for a
multi operation including the power codes of other brands, always check that the power of all the components has turned off.
RECEIVER
SOURCE
MAIN
MULTI
OPERATION
ZONE2
3
DVD
iPod
USB
OPTION
MULTI CH
ADAPTER
NET RADIO
CD
TUNER
HMG
BD
TV
HDMI
DVR
BDR
1
2
MULTI
OPERATION
RECEIVER
SOURCE
MAIN
MULTI
OPERATION
ZONE2
3
DVD
iPod
USB
OPTION
MULTI CH
ADAPTER
NET RADIO
CD
TUNER
HMG
BD
TV
HDMI
DVR
BDR
1
2
MULTI
OPERATION
DVD
RECEIVER
SOURCE
MAIN
MULTI
OPERATION
AUDIO
PARAMETER
TOP MENU
iPod CTRL
PTY SEARCH
CATEGORY
LIST
TOOLS
HOME
MENU
STATUS
THX
PQLS
MPX
MEMORY
PHASE CTRL
CH LEVEL
T.EDIT
GUIDE
GUIDE
VIDEO
PARAMETER
ZONE2
SOURCE
TV
RECEIVER
3
iPod
USB
OPTION
MULTI CH
ADAPTER
NET RADIO
INPUT SELECT
LIGHT
CD
PHONO
AUX
INPUT
MUTE
TUNE
TUNE
PRESET
PRESET
MUTE
PGM
MENU
VOL
VOL
TV CONTROL
CH
VIDEO
CD-R
STEREO
SIGNAL SEL SLEEP
AUDIO
INFO
DIMMER
A.ATT
CLR
SBch
MCACC
HDMI OUT
D.ACCESS
ENTER
CLASS
DISP
CH
AUTO/ALC/
DIRECT
STANDARD ADV SURR
IN
TUNER
HMG
BD
TV
HDMI
DVR
BDR
1
2
ENTER
RETURN
BAND
SC-37_35_UXJCB.book 88 ページ ２０１０年３月９日 火曜日 午前９時３２分