Panasonic WV-NP472 - Manual (Page 20)

-20-
Manual Fine Adjustment for AWC (ATW)
You can set the white balance items manually.
1. To set MASK SET, proceed as described in steps 2
to 4 of “ALC mode with SUPER-D2 OFF and ELC
mode”.
2. Move the cursor to R.
3. Press
L or M to obtain the optimum amount of
red gain.
4. Move the cursor to B.
5. Press
L or M to obtain the optimum amount of
blue gain.
Note: When you need to set MASK SET, re-adjust to
obtain the optimum amount of red and blue gain.
7. Motion Detector Setting (MOTION DET)
The camera detects moving objects in the scene by
monitoring changes in brightness level. You can select
the level of sensitivity for motion detection.
When this camera is connected to a compatible intelli-
gent CCTV system, the camera transmits an alarm sig-
nal by multiplexing it with the video signal.
1. Move the cursor to MOTION DET and select ON.
The factory default setting is OFF.
2. Press I. The MOTION DETECT menu appears
on the monitor screen.
** MOTION DETECT **
LEVEL ....I....
- +
DISPLAY MODE
ALARM OFF
MASK SET
RET END
↵
↵
3. Move the cursor to MASK SET and press
I.
MASK SET lets you set 48 mask areas. To set
MASK SET, proceed as described in steps 2 to 4 of
“ALC mode with SUPER-D2 OFF and ELC mode”.
4. Move the cursor to ALARM and select ON or OFF
to set the alarm for DISPLAY MODE.
Note: When using the WV-RM70, WV-CU550
series, WV-CU161 or WV-CU360 controller
with this model, select OFF for ALARM.
5. Move the cursor to DISPLAY MODE and press
I
to see the current setting. The masks that detect
the brightness changes start blinking.
6. To raise detection sensitivity, press
I to return to
the MOTION DETECT menu.
7. To obtain the optimum detection level, move the “I”
cursor to adjust the level.
8. Repeat the procedure above to obtain a satisfacto-
ry setting.
Notes:
• When the camera is not used in a Panasonic
Intelligent CCTV System, select OFF.
Otherwise, video equipment may malfunction
because of the alarm signal misinterpretation for a
time code signal.
• The motion detector may malfunction when the
lightening equipment continuously turns on and off,
or when ELC mode is selected for ALC/ELC.
• Set MASK SET over the areas where swaying
leaves, curtains, or other objects are detected.
• Adjust the detection level on the menu to prevent
misinterpretation under low light conditions with
noise.
• It takes about 0.2 seconds for the alarm signal to
reach the VCR’s alarm terminal after the camera
detects a moving object.
• The motion detector is not specifically intended to
prevent theft or fire.
8. Lens Drive Signal Selection (LENS DRIVE)
Select a signal form matching to the lens installed. The
factory setting is DC.
DC: Is applied to a DC driven type lens.
VIDEO: Is applied to a video signal type lens.
** CLOCK **
CLOCK TYPE MM/DD/YYYY
RET END
9. Date Display (Clock) Setting
You can select a display position and a style of the date
display. The camera ID will be displayed under the
position designated here.
1. In the camera setup menu, move the cursor to
CLOCK, and press
M or L to select a display
position.
OFF: Does not display the date.
ON (L-UP): Displays at the left-upper corner.
ON (L-LOW): Displays at the left-lower corner.
ON (R-UP): Displays at the right-upper corner.
ON (R-LOW): Displays at the right-lower corner.
2. Move the cursor to CLOCK, and press I.
The CLOCK menu opens.
3. Select a style with
L and M.
YYYY/MM/DD: Year/Month/Day
MM/DD/YYYY: Month/Day/Year
DD/MM/YYYY: Day/ Month/Year