Plus Corporation UP-1100 - Manual (Page 29)

E – 29
All the menu items and CUSTOM 1 to 5 memory can be reset to the
factory settings except for the followings:
• LANGUAGE
• LAMP USAGE
1 Press MENU to display the main menu.
2 Press the cursor / key to select “SETTING MENU.”
3 Press L-CLICK to display the SETTING MENU.
4 Press the cursor / key to select “ALL RESET.”
5 Press the cursor + key for more than three seconds.
“COMPLETE” appears under the title “ALL RESET”
after the reset has completed.
R e s e t t i n g a l l t o t h e
f a c t o r y s e t t i n g s
If you activate the on-screen function,
• The input source “VIDEO,” “S-VIDEO,” or “RGB” will be
displayed for three seconds when you have selected the input
source with the remote control (see page 16), and
• The message “POWER OFF/ENTER” will be displayed on the
screen when you press the POWER button on the unit, if “DIS-
PLAY” is set to “ON” for preventing the unit from being turned
off accidentally.
1 Press MENU to display the main menu.
2 Press the cursor / key to select “SETTING MENU.”
3 Press L-CLICK to display the SETTING MENU.
4 Press the cursor / key to select “DISPLAY,” then press
the cursor + key to select “ON” to activate the on-screen
function.
To deactivate the function, set “DISPLAY” to “OFF” by
pressing the cursor – key.
Turning off the unit
• Operating with the remote control
Press the POWER OFF button a little bit longer.
The unit will go off regardless of the “POWER OFF” setting.
• Operating with the unit
When “DISPLAY” is set to “ON”
1 Press the POWER button.
“POWER OFF/ENTER” appears on the screen.
2 Press ENTER.
The unit will go off.
When “DISPLAY” is set to “OFF”
Press the POWER button a little bit longer.
The unit will go off.
Canceling turing off the unit when
“POWER OFF/ENTER” is appearing on the
screen
A c t i v a t i n g t h e o n –
s c r e e n f u n c t i o n
The lamp housing must be replaced after 1000 hours of use. When
1000 hours have elapsed the STATUS indicator will light in red (see
page 31). Periodically check hours of lamp use in the menu so that
you will have time to purchase a new lamp housing before the old
one is burnt out.
1 Press MENU to display the main menu.
2 Press the cursor / key to select “POWER MENU.”
3 Press L-CLICK to display the POWER MENU.
4 Press the cursor / key to select “LAMP USAGE.”
The lamp use hours will be displayed.
Resetting the lamp use hours to zero
You need to reset the lamp use hours to zero after replacing the lamp
housing (see page 32).
1 Carry out the steps above.
2 Press the POWER ON button on the remote control for
more than ten seconds.
“LAMP USAGE” will be set to zero.
If the unit doesn’t go on because lamp
use exceeds 1100 hours.
The unit is designed not to turn on after the lamp use has exceeded
1100 hours. (If the unit is in use, it will go off.) If this happened you
must replace the lamp housing with a new one immediately. After
replacing the lamp housing, you need to reset the lamp use hours to
zero to enable you to turn on the unit.
1 Switch on the main power (see step 1 on page 16).
2 Press the POWER OFF button on the remote control for
more ten seconds.
“LAMP USAGE” will be reset to zero and the STATUS
indicator will go off (see page 31).
C h e c k i n g h o u r s
o f l a m p u s e
• Operating with the remote control
– Press MAGNIFY – to turn off the message, or
– Press MENU to display the main menu.
• Operating with the unit
– Press ADJUST + to change the message on the screen to
“POWER OFF/CANCEL,” then press ENTER, or
– Press MENU to display the main menu.