Panasonic PT-47WX54 - Manual (Page 31)

I CON M ENUS O PERATION
29 z
ENGLISH
SET UP (cont.)
ˆ CONVERGE (cont.)
Note: After selecting, press VOL to activate RESET TO
DEFAULT feature. When using this feature in Zoom
mode, the effect can only be verified when you exit all
menus and display normal picture.
CONVERGENCE ADJ.
Procedure
• After pressing VOL the align Green to Center screen
will be displayed.
• Then use the navigation buttons on the remote control
to align the horizontal and vertical green lines on screen,
with the cabinet reference marks on top center and left
center of cabinet, as shown below.
• Press to display red center correction screen.
• Use the navigation buttons on the remote control to align
the red cross with the white cross pattern at the center of
the screen.
Note:
To prevent picture tube damage, do not leave
test pattern on for an extended period of time.
• Then press “0” on the remote control keypad to display
the BLUE center correction screen, repeat procedure for
adjusting blue. If needed press “0” again to return to
RED correction screen.
Note: An adjusted cross pattern appears white with a minimum
of color protrusion.
NINE POINT CONVERGENCE CORRECTION
Note: Remote Control must be in TV mode.
Procedure
• Press to display red correction screen.
• Press the 1 through 9 keypad buttons on the remote
control to select the desired convergence position.
• Use the navigation buttons to align the RED cross with
the white cross pattern.
Note: An adjusted cross pattern appears white with a minimum
of color protrusion.
• Press “0” on the remote control keypad to display the
BLUE correction screen, then repeat procedure.
• To exit press repeatedly, then press CH .
ˆ OTHER ADJ.
Highlight OTHER ADJ. and press VOL to enter sub sub-
menu field.
Note: While sub sub-menu features are highlighted, press
VOL to adjust or activate.
• MODE - To select TV (antenna) or CABLE mode
depending on the signal source.
• AUTO PROGRAM - To automatically program all
channels received through the RF input.
• MANUAL PROGRAM - To manually add or delete
channels.
• AUTO POWER ON - Select SET to power up the TV at
the same time as the Cable box or other components or
select OFF.
• CHAN BANNER - Select ON to display onscreen banner
when changing channels.
• IMAGE SHIFT - Selecting ON is recommended for this
feature to prevent image retention on screen.
SET UP
CONVERGE.
PRESS ACTION TO RETURN
CONVERGENCE ADJ.
RESET TO DEFAULT
PRESS CH AND VOL KEY TO
ALIGN GREEN LINES TO THE
CENTER MARK ON THE CABINET
LEFT RIGHT
UP
DOWN
PRESS ACTION TO CONTINUE
Reference Marks
Front of cabinet
ACTION
LEFT RIGHT
UP
DOWN
PRESS ACTION TO CONTINUE
IF RED IS PROTRUDING FROM
CENTER CROSS, PRESS CH AND
VOL KEY TO CORRECT
PRESS 0 TO ADJUST BLUE
K
K
K
K
LEFT RIGHT
UP
DOWN
PRESS ACTION TO CONTINUE
IF BLUE IS PROTRUDING FROM
CENTER CROSS, PRESS CH AND
VOL KEY TO CORRECT
PRESS 0 TO ADJUST BLUE
Press
“0”
ACTION
PRESS ACTION TO EXIT
1 2 3
4 6
7 8 9
PRESS ACTION TO EXIT
PRESS 0 TO ADJUST BLUE
CORRECTING RED
PRESS # KEY TO SELECT POS.
PRESS CH AND VOL KEY TO CORR.
PRESS ACTION TO EXIT
1 2 3
4 6
7 8 9
PRESS ACTION TO EXIT
PRESS 0 TO ADJUST BLUE
CORRECTING RED
PRESS # KEY TO SELECT POS.
PRESS CH AND VOL KEY TO CORR.
PRESS ACTION TO EXIT
1 2 3
4 6
7 8 9
PRESS ACTION TO EXIT
PRESS 0 TO ADJUST RED
CORRECTING BLUE
PRESS # KEY TO SELECT POS.
PRESS CH AND VOL KEY TO CORR.
Press
“0”
ACTION
SET UP
OTHER ADJ .
PRESS ACTION TO RETURN
MODE
AUTO PROGRAM
MANUAL PROGRAM
AUTO POWER ON
CHAN BANNER
IMAGE SHIFT
OFF
ON
CABLE
ON